View Z8L18006FEC_27508.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

PRELIMINARY PRODUCT SPECIFICATION
1
Z80180/Z8S180/ Z8L180 SL1919
ENHANCED Z180 MICROPROCESSOR
FEATURES
s s s s s s s s s
1
Code Compatible with Zilog Z80(R) CPU Extended Instructions Two Chain-Linked DMA Channels Low Power-Down Modes On-Chip Interrupt Controllers Three On-Chip Wait-State Generators On-Chip Oscillator/Generator Expanded MMU Addressing (up to 1 MB) Clocked Serial I/O Port
s s s s s s s
Two 16-Bit Counter/Timers Two Enhanced UARTs (up to 512 Kbps) Clock Speeds: 6, 8, 10, 20, 33 MHz Operating Range: 5V (3.3V@ 20 MHz) Operating Temperature Range: 0C to +70C -40C to +85C Extended Temperature Range Three Packaging Styles - 68-Pin PLCC - 64-Pin DIP - 80-Pin QFP
GENERAL DESCRIPTION
The enhanced Z80180/Z8S180/Z8L180TM significantly improves on the previous Z80180 models while still providing full backward compatibility with existing Zilog Z80 devices. The Z80180/Z8S180/Z8L180 now offers faster execution speeds, power saving modes, and EMI noise reduction. This enhanced Z180 design also incorporates additional feature enhancements to the ASCIs, DMAs, and Icc STANDBY Mode power consumption. With the addition of "ESCC-like" Baud Rate Generators (BRGs), the two ASCIs now have the flexibility and capability to transfer data asynchronously at rates of up to 512 Kbps. In addition, the ASCI receiver has added a 4-byte First In First Out (FIFO) which can be used to buffer incoming data to reduce the incidence of overrun errors. The DMAs have been modified to allow for a "chain-linking" of the two DMA channels when set to take their DMA requests from the same peripherals device. This feature allows for non-stop DMA operation between the two DMA channels, reducing the amount of CPU intervention (Figure 1). Not only does the Z80180/Z8S180/Z8L180 consume less power during normal operations than the previous model, it has also been designed with three modes intended to further reduce the power consumption. Zilog reduced Icc power consumption during STANDBY Mode to a minimum of 10 A by stopping the external oscillators and internal clock. The SLEEP mode reduces power by placing the CPU into a "stopped" state, thereby consuming less current while the on-chip I/O device is still operating. The SYSTEM STOP mode places both the CPU and the onchip peripherals into a "stopped" mode, thereby reducing power consumption even further. A new clock doubler feature has been implemented in the Z80180/Z8S180/Z8L180 device that allows the programmer to double the internal clock from that of the external clock. This provides a systems cost savings by allowing the use of lower cost, lower frequency crystals instead of the higher cost, and higher speed oscillators. The Enhanced Z180 is housed in 80-pin QFP, 68-pin PLCC, and 64-pin DIP packages. DS971800401 PRELIMINARY 1-1
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor Notes: All Signals with a preceding front slash, "/" are active Low, for example, B//W (WORD is active Low); /B/W (BYTE is active Low, only). Alternatively, an overslash may be used to signify active Low, for example WR
Zilog Power connections follow conventional descriptions below: Connection Power Ground Circuit VCC GND Device VDD VSS
/BUSREQ
/RESET
/BUSACK
/MREQ
EXTAL
/RFSH
/HALT
/WAIT
IORQ
XTAL
INT0
INT1
/RD
O
Timing Generator
Bus State Control CPU
Interrupt
A18/TOUT
16-bit Programmable Reload Timers (2)
/DREQ1 DMACS (2) TEND1
TXS RXS/CTS1 CKS
Clocked Serial I/O Port Address Bus (16-Bit) Data Bus (8-Bit)
TXA0 Asynchronous SCI (Channel 0) CKA0, /DREQ0 RXA0 /RTS0 /CTS0 /DCD0
TXA1 Asynchronous SCI (Channel 1) CKA1, /TEND0 RXA1
MMU
Address Buffer
Data Buffer
VCC VSS
A19-A0
D7-D0
Figure 1. Z80180/Z8S180/Z8L180 Functional Block Diagram
1-2
PRELIMINARY
DS971800401
INT2
/NMI
/WR
/M1
ST
E
Zilog
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
PIN DESCRIPTION
VSS XTAL EXTAL /WAIT /BUSACK /BUSREQ /RESET /NMI /INT0 /INT1 /INT2 ST A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18/TOUT VCC
1
64
Z80180 64Pin DIP
32
33
PHI /RD /WR /M1 E /MREQ /IORQ /RFSH /HALT /TEND1 /DREQ CKS RXS//CTS TXS CKA1//TEND0 RXA1 TXA1 CKA//DREQ0 RXA0 TXA0 /DCD0 /CTS0 /RTS0 D7 D6 D5 D4 D3 D2 D1 D0 VSS
1
Figure 2. Z80180 64-Pin DIP Pin Configuration
DS971800401
PRELIMINARY
1-3
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
Zilog
/INT0 /INT1 /INT2 ST A0 A1 A2 A3 VSS A4 A5 A6 A7 A8 A9 A10 A11
9 10
/NMI /RESET /BUSREQ /BUSACK /WAIT EXTAL XTAL VSS VSS PHI /RD /WR /M1 E /MREQ /IORQ /RFSH 1 61 60
Z80180/Z8S180/ Z8L180 68-Pin PLCC
/HALT /TEND1 /DREQ1 CKS RXS//CTS1 TXS CKA1//TEND0 RXA1 TEST TXA1 CKA0//DREQ0 RXA0 TXA0 /DCD0 /CTS0 /RTS0 D7
27
43
Figure 3. Z80180/Z8S180/Z8L180 68-Pin PLCC Pin Configuration
1-4
A12 A13 A14 A15 A16 A17 A18/TOUT VCC A19 VSS D0 D1 D2 D3 D4 D5 D6
PRELIMINARY
DS971800401
Zilog
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
/RFSH N/C N/C /HALT /TEND1 /DREQ1 CKS RXS/CTS1 TXS CKA1//TEND0 RXA1 TEST TXA1 N/C CKA0//DREQ0 RXA0 TXA0 /DCD0 /CTS0 /RTS0 D7 N/C N/C D6
1
64 /IORQ /MREQ E /M1 /WR /RD PHI VSS VSS XTAL N/C EXTAL /WAIT /BUSACK /BUSREQ /RESET 65
60
55
50
45
41 40 D5 D4 D3 D2 D1 D0 VSS A19 VCC A18/TOUT NC A17 A16 A15 A14 A13
Z80180/Z8S180/Z8L180 80-Pin QFP
1
5
10
15
20
24
DS971800401
/NMI N/C N/C /INT0 /INT1 /INT2 ST A0 A1 A2 A3 VSS A4 N/C A5 A6 A7 A8 A9 A10 A11 N/C N/C A12
Figure 4. Z80180/Z8S180/Z8L180 80-Pin QFP Pin Configuration
PRELIMINARY
1-5
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor Table 1. Z80180/Z8S180/Z8L180 Pin Identification Pin Number and Package Type QFP 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 1-6 PLCC 9 DIP 8 Default Function /NMI NC NC /INT0 /INT1 /INT2 ST A0 A1 A2 A3 VSS A4 NC A5 A6 A7 A8 A9 A10 A11 NC NC A12 A13 A14 A15 A16 A17 NC A18 VCC A19 VSS D0 D1 D2 D3 D4 D5 D6 NC NC D7 /RTS0 PRELIMINARY Secondary Function
Zilog
Control
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43
25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
/TOUT
Bit 2 or Bit 3 of TCR
44 45
41 42
DS971800401
Zilog
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor Table 1. Z80180/Z8S180/Z8L180 Pin Identification
Pin Number and Package Type QFP 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 PLCC 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 DIP 43 44 45 46 47 48 49 50 51 52 53 54 55 56 Default Function /CTS0 /DCD0 TXA0 RXA0 CKA0 NC TXA1 TEST RXA1 CKA1 TXS RXS CKS /DREQ1 /TEND1 /HALT NC NC /RFSH /IORQ /MREQ E M1 /WR /RD PHI VSS VSS 2 3 4 5 6 7 XTAL NC EXTAL /WAIT /BUSACK /BUSREQ /RESET
Secondary Function
Control
1
/DREQ0
Bit 3 or Bit 5 of DMODE
/TEND0 /CTS1
Bit 4 of CNTLA1 Bit 2 of STAT1
61 62 63 64 65 66 67 68 1 2 3 4 5 6 7 8
57 58 59 60 61 62 63 64 1
DS971800401
PRELIMINARY
1-7
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor Table 2. Pin Status During RESET BUSACK and SLEEP Pin Number and Package Type QFP 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 1-8 PLCC 9 DIP 8 Default Function /NMI NC NC /INT0 /INT1 /INT2 ST A0 A1 A2 A3 VSS A4 NC A5 A6 A7 A8 A9 A10 A11 NC NC A12 A13 A14 A15 A16 A17 NC A18 VCC A19 VSS D0 D1 D2 D3 D4 D5 D6 NC NC D7 PRELIMINARY Secondary Function RESET IN Pin Status BUSACK IN
Zilog
SLEEP
IN
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
IN IN IN 1 3T 3T 3T 3T GND 3T 3T 3T 3T 3T 3T 3T 3T
IN IN IN ? 3T 3T 3T 3T GND 3T 3T 3T 3T 3T 3T 3T 3T
IN IN IN 1 1 1 1 1 GND 1 1 1 1 1 1 1 1
27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43
25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
3T 3T 3T 3T 3T 3T /TOUT 3T VCC 3T GND 3T 3T 3T 3T 3T 3T 3T
3T 3T 3T 3T 3T 3T 3T VCC 3T GND 3T 3T 3T 3T 3T 3T 3T
1 1 1 1 1 1 1 VCC 1 GND 3T 3T 3T 3T 3T 3T 3T
44
41
3T
3T
3T DS971800401
Zilog
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor Table 2. Pin Status During RESET BUSACK and SLEEP
Pin Number and Package Type QFP 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 PLCC 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 DIP 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 Default Function /RTS0 /CTS0 /DCD0 TXA0 RXA0 CKA0 NC TXA1 TEST RXA1 CKA1 TXS RXS CKS /DREQ1 /TEND1 /HALT NC NC /RFSH /IORQ /MREQ E /M1 /WR /RD PHI VSS VSS 2 3 4 5 6 7 XTAL NC EXTAL /WAIT /BUSACK /BUSREQ /RESET Secondary Function RESET 1 IN IN 1 IN 3T 1 IN 3T 1 IN 3T IN 1 1
Pin Status BUSACK OUT OUT IN OUT IN OUT OUT IN IN OUT IN I/O 3T OUT 1
1
SLEEP
1 IN IN OUT IN OUT OUT IN IN OUT IN I/O IN 1 0
/DREQ0
/TEND0 /CTS1
61 62 63 64 65 66 67 68 1 2 3 4 5 6 7 8
57 58 59 60 61 62 63 64 1
1 1 1 0 1 1 1 OUT GND GND OUT IN IN 1 IN IN
OUT 3T 3T OUT 1 3T 3T OUT GND GND OUT IN IN OUT IN IN
OUT 1 1 OUT 1 1 1 OUT GND GND OUT IN IN OUT IN IN
DS971800401
PRELIMINARY
1-9
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
Zilog
PIN DESCRIPTIONS
A0-A19. Address Bus (Output, active High, tri-state). A0A19 form a 20-bit address bus. The Address Bus provides the address for memory data bus exchanges, up to 1 MB, and I/O data bus exchanges, up to 64K. The address bus enters a high-impedance state during reset and external bus acknowledge cycles. Address line A18 is multiplexed with the output of PRT channel 1 (TOUT, selected as address output on reset) and address line A19 is not available in DIP versions of the Z80180. BUSACK. Bus Acknowledge (Output, active Low). /BUSACK indicated the requesting device, the MPU address and data bus, and some control signals, have entered their high-impedance state. /BUSREQ. Bus Request (Input, active Low). This input is used by external devices (such as DMA controllers) to request access to the system bus. This request has a higher priority than /NMI and is always recognized at the end of the current machine cycle. This signal will stop the CPU from executing further instructions and places address and data buses, and other control signals, into the high-impedance state. CKA0, CKA1. Asynchronous Clock 0 and 1 (Bidirectional, active High). When in output mode, these pins are the transmit and receive clock outputs from the ASCI baud rate generators. When in input mode, these pins serve as the external clock inputs for the ASCI baud rate generators. CKA0 is multiplexed with /DREQ0, and CKA1 is multiplexed with /TEND0. CKS. Serial Clock (Bidirectional, active High). This line is clock for the CSIO channel. PHI CLOCK. System Clock (Output, active High). The output is used as a reference clock for the MPU and the external system. The frequency of this output is equal to onehalf that of the crystal or input clock frequency. /CTS0 - /CTS1. Clear to send 0 and 1 (Inputs, active Low). These lines are modem control signals for the ASCI channels. /CTS1 is multiplexed with RXS. D0 - D7. Data Bus = (Bidirectional, active High, tri-state). D0 - D7 constitute an 8-bit bi-directional data bus, used for the transfer of information to and from I/O and memory devices. The data bus enters the high-impedance state during reset and external bus acknowledge cycles. DCD0. Data Carrier Detect 0 (Input, active Low). This is a programmable modem control signal for ASCI channel 0. /DREQ0, /DREQ1. DMA Request 0 and 1 (Input, active Low). /DREQ is used to request a DMA transfer from one of the on-chip DMA channels. The DMA channels monitor these inputs to determine when an external device is ready for a read or write operation. These inputs can be programmed to be either level or edge sensed. /DREQ0 is multiplexed with CKA0. E. Enable Clock (Output, active High). Synchronous machine cycle clock output during bus transactions. EXTAL. External Clock Crystal (Input, active High). Crystal oscillator connections. An external clock can be input to the Z80180/Z8S180/Z8L180 on this pin when a crystal is not used. This input is Schmitt triggered. /HALT. Halt/SLEEP (Output, active Low). This output is asserted after the CPU has executed either the HALT or SLP instruction, and is waiting for either non-maskable or maskable interrupt before operation can resume. It is also used with the /M1 and ST signals to decode status of the CPU machine cycle. /INT0. Maskable Interrupt Request 0 (Input, active Low). This signal is generated by external I/O devices. The CPU will honor these requests at the end of the current instruction cycle as long as the /NMI and /BUSREQ signals are inactive. The CPU acknowledges this interrupt request with an interrupt acknowledge cycle. During this cycle, both the /M1 and /IORQ signals will become active. /INT1, /INT2. Maskable Interrupt Request 1 and 2 (Inputs, active Low). This signal is generated by external I/O devices. The CPU will honor these requests at the end of the current instruction cycle as long as the /NMI, /BUSREQ, and /INT0 signals are inactive. The CPU will acknowledge these requests with an interrupt acknowledge cycle. Unlike the acknowledgment for /INT0, during this cycle neither the /M1 or /IORQ signals will become active. /IORQ. I/O Request (Output, active Low, tri-state). /IORQ indicates that the address bus contains a valid I/O address for an I/O read or I/O write operation. /IORQ is also generated, along with /M1, during the acknowledgment of the /INT0 input signal to indicate that an interrupt response vector can be place onto the data bus. This signal is analogous to the /IOE signal of the Z64180. /M1. Machine Cycle 1 (Output, active Low). Together with /MREQ, /M1 indicates that the current cycle is the Opcode fetch cycle of and instruction execution. Together with /IORQ, /M1 indicates that the current cycle is for an interrupt acknowledge. It is also used with the /HALT and ST signal to decode status of the CPU machine cycle. This signal is analogous to the /LIR signal of the Z64180. /MREQ. Memory Request (Output, active Low, tri-state). /MREQ indicates that the address bus holds a valid address for a memory read or memory write operation. This signal is analogous to the /ME signal of Z64180.
1-10
PRELIMINARY
DS971800401
Zilog /NMI. Non-maskable Interrupt (Input, negative edge triggered). /NMI has a higher priority than /INT and is always recognized at the end of an instruction, regardless of the state of the interrupt enable flip-flops. This signal forces CPU execution to continue at location 0066H. /RD. ReOpcoded (Output, active Low, tri-state). /RD indicated that the CPU wants to read data from memory or an I/O device. The addressed I/O or memory device should use this signal to gate data onto the CPU data bus. /RFSH. Refresh (Output, active Low). Together with /MREQ, /RFSH indicates that the current CPU machine cycle and the contents of the address bus should be used for refresh of dynamic memories. The low order 8 bits of the address bus (A7 - A10) contain the refresh address. This signal is analogous to the /REF signal of the Z64180. /RTS0. Request to Send 0 (Output, active Low). This is a programmable modem control signal for ASCI channel 0. RXA0, RXA1. Receive Data 0 and 1 (Input, active High). These signals are the receive data to the ASCI channels. RXS. Clocked Serial Receive Data (Input, active High). This line is the receiver data for the CSIO channel. RXS is multiplexed with the /CTS1 signal for ASCI channel 1. ST. Status (Output, active High). This signal is used with the /M1 and /HALT output to decode the status of the CPU machine cycle. Table 3. Status Summary ST 0 1 1 0 0 1
/HALT /M1
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor TOUT. Timer Out (Output, active High). TOUT is the pulse output from PRT channel 1. This line is multiplexed with A18 of the address bus. TXA0, TXA1. Transmit Data 0 and 1 (Outputs, active High). These signals are the transmitted data from the ASCI channels. Transmitted data changes are with respect to the falling edge of the transmit clock. TXS. Clocked Serial Transmit Data (Output, active High). This line is the transmitted data from the CSIO channel. /WAIT. Wait (Input, active Low). /WAIT indicated to the MPU that the addressed memory or I/O devices are not ready for a data transfer. This input is sampled on the falling edge of T2 (and subsequent wait states). If the input is sampled Low, then the additional wait states are inserted until the /WAIT input is sampled high, at which time execution will continue. /WR. Write (Output, active Low, tri-state). /WR indicated that the CPU data bus holds valid data to be stored at the addressed I/O or memory location. XTAL. Crystal (Input, active High). Crystal oscillator connection. This pin should be left open if an external clock is used instead of a crystal. The oscillator input is not a TTL level (reference DC characteristics). Several pins are used for different conditions, depending on the circumstance.
1
Multiplexed Pin Descriptions
Operation CPU Operation (1st opcode fetch) CPU Operation (2nd opcode and 3rd Opcode fetch) CPU Operation (MC except for Opcode fetch) DMA Operation HALT Mode SLEEP Mode (including SYSTEM STOP Mode) During RESET, this pin is initialized as A18 pin. If either TOC1 or TOC0 bit of the Timer Control Register (TCR) is set to 1, TOUT function is selected. If TOC1 and TOC0 are cleared to 0, A18 function is selected. CKA0 / /DREQ0 During RESET, this pin is initialized as CKA0 pin. If either DM1 or SM1 in DMA Mode Register (DMODE) is set to 1, /DREQ0 function is always selected. CKA1 / /TEND0 During RESET, this pin is initialized as CKA1 pin. If CKA1D bit in ASCI control register ch1 (CNTLA1) is set to 1, /TEND0 function is selected. If CKA1D bit is set to 0, CKA1 function is selected. RXS / /CTS1 During RESET, this pin is initialized as RXS pin. If CTS1E bit in ASCI status register ch1 (STAT1) is set to 1, /CTS1 function is selected. If CTS1E bit is set to 0, RXS function is selected. A18 / /TOUT
1 1 1 X 0 0
0 0 1 1 0 1
Notes: X = Reserved MC = Machine Cycle
/TEND0, /TEND1. Transfer End 0 and 1 (Outputs, active Low). This output is asserted active during the last write cycle of a DMA operation. It is used to indicate the end of the block transfer. /TEND0 is multiplexed with CKA1. TEST. Test (Output, not in DIP version). This pin is for test and should be left open.
DS971800401
PRELIMINARY
1-11
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
Zilog
ARCHITECTURE
The Z180(R) combines a high-performance CPU core with a variety of system and I/O resources useful in a broad range of applications. The CPU core consists of five functional blocks: clock generator, bus state controller, Interrupt controller, memory management unit (MMU), and the central processing unit (CPU). The integrated I/O resources make up the remaining four function blocks: direct memory access (DMA) control (2 channels), asynchronous serial communication interface (ASCI, 2 channels) programmable reload timers (PRT, 2 channels), and a clock serial I/O (CSIO) channel. Clock Generator. Generates system clock from an external crystal or clock input. The external clock is divided by two or one and provided to both internal and external devices. Bus State Controller. This logic performs all of the status and bus control activity associated with both the CPU and some on-chip peripherals. This includes wait-state timing, reset cycles, DRAM refresh, and DMA bus exchanges. Interrupt Controller. This logic monitors and prioritizes the variety of internal and external interrupts and traps to provide the correct responses from the CPU. To maintain compatibility with the Z80(R) CPU, three different interrupts modes are supported. Memory Management Unit. The MMU allows the user to "map" the memory used by the CPU (logically only 64KB) into the 1 MB addressing range supported by the Z80180/Z8S180/Z8L180. The organization of the MMU object code maintains compatibility with the Z80 CPU, while offering access to an extended memory space. This is accomplished by using an effective "common areabanked area" scheme. Central Processing Unit. The CPU is microcoded to provide a core that is object-code compatible with the Z80 CPU. It also provides a superset of the Z80 instruction set, including 8-bit multiply. The core has been modified to allow many of the instructions to execute in fewer clock cycles. DMA Controller. The DMA controller provides high speed transfers between memory and I/O devices. Transfer operations supported are memory-to-memory, memory to/from I/O, and I/O-to-I/O. Transfer modes supported are request, burst, and cycle steal. DMA transfers can access the full 1 MB address range with a block length up to 64 KB, and can cross over 64K boundaries. Asynchronous Serial Communication Interface (ASCI). The ASCI logic provides two individual full-duplex UARTs. Each channel includes a programmable baud rate generator and modem control signals. The ASCI channels can also support a multiprocessor communication format as well as break detection and generation. Programmable Reload Timers (PRT). This logic consists of two separate channels, each containing a 16-bit counter (timer) and count reload register. The time base for the counters is derived from the system clock (divided by 20) before reaching the counter. PRT channel 1 provides an optional output to allow for waveform generation.
1-12
PRELIMINARY
DS971800401
Zilog
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
Timer Data Register Write (0004H) Reset Timer Data Register FFFFH 0004H
0 < t < 20 20 20
20
20
20
20
20
20
20
1
0003H 0002H
0001H 0000H 0003H 0002H 0001H 0000H 0003H
Timer Reload Register Write (0003H) Timer Reload Register
Reload
Reload
FFFFH
0003H Write "1" to TDE
TDE Flag
TIF Flag
Timer Data Register Read Timer Control Requestor Read
Figure 5. Timer Initialization, Count Down, and Reload Timing
Timer Data Reg. = 0001H
Timer Data Reg. = 0000H
TOUT
Figure 6. Timer Output Timing
DS971800401
PRELIMINARY
1-13
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor Clocked Serial I/O (CSI/O). The CSIO channel provides a half-duplex serial transmitter and receiver. This channel can be used for simple high-speed data connection to another microprocessor or microcomputer. TRDR is used for both CSI/O transmission and reception. Thus, the system design must ensure that the constraints of half-duplex operation are met (Transmit and Receive operation cannot occur simultaneously). For example, if a CSI/O transmis-
Zilog sion is attempted while the CSI/O is receiving data, a CSI/O will not work. Also note that TRDR is not buffered. Therefore, attempting to perform a CSI/O transmit while the previous transmit data is still being shifted out causes the shift data to be immediately updated, thereby corrupting the transmit operation in progress. Similarly, reading TRDR while a transmit or receive is in progress should be avoided.
Internal Address/Data Bus
TXS RXS
CSI/O Transmit/Receive Data Register: TRDR (8) CSI/O Control Register: CNTR (8)
Baud Rate Generator
CKS
Interrupt Request
Figure 7. CSIO Block Diagram
OPERATION MODES
Z80(R) versus 64180 Compatibility. The Z80180/Z8S180/Z8L180 is descended from two different "ancestor" processors, Zilog's original Z80 and the Hitachi 64180. The Operating Mode Control Register (OMCR), shown in Figure 8, can be programmed to select between certain Z80 and 64180differences. -- --- -Reserved /IOC (R/W) /M1TE (W) M1E (R/W) M1E (M1 Enable). This bit controls the M1 output and is set to a 1 during reset. When M1E=1, the M1 output is asserted Low during the opcode fetch cycle, the INT0 acknowledge cycle, and the first machine cycle of the NMI acknowledge. On the Z80180/Z8S180/Z8L180, this choice makes the processor fetch an RETI instruction once, and when fetching an RETI from zero-wait-state memory will use three clock machine cycles, which are not fully Z80-timing compatible but are compatible with the on-chip CTCs. When M1E=0, the processor does not drive M1 Low during instruction fetch cycles, and after fetching an RETI instruction once with normal timing, it goes back and re-fetches the instruction using fully Z80-compatible cycles that include driving M1 Low. This may be needed by some external Z80 peripherals to properly decode the RETI instruction. Figure 9 and Table 4 show the RETI sequence when M1E=0.
D7 D6 D5 --
Figure 8. Operating Control Register (OMCR: I/O Address = 3EH)
1-14
PRELIMINARY
DS971800401
Zilog T1 T2 T3 T1 T2 T3 TI TI TI T1 T2 T3
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor TI T1 T2 T3 TI
A0-A18 (A19) D0-D7 M1 MREQ RD ST
PC EDH 4DH
PC+1
PC EDH
PC+1 4DH
1
Figure 9. RETI Instruction Sequence with MIE=0
Table 4. RETI Control Signal States with MIE=0 Machine Cycle States 1 2 T1-T3 T1-T3 Ti Ti Ti T1-T3 Ti T1-T3 T1-T3 T1-T3 M1 IOC=1 IOC=0 0 0 1 1 1 0 1 0 1 1 1 1 1 1 1 0 1 1 1 1
Address 1st Opcode 2nd Opcode NA NA NA 1st Opcode NA 2nd Opcode SP SP+1
Data EDH 4DH Tri-State Tri-State Tri-State EDH Tri-State 4DH Data Data
RD 0 0 1 1 1 0 1 0 0 0
WR 1 1 1 1 1 1 1 1 1 1
MREQ 0 0 1 1 1 0 1 0 0 0
IORQ 1 1 1 1 1 1 1 1 1 1
HALT 1 1 1 1 1 1 1 1 1 1
ST 0 0 1 1 1 1 1 1 1 1
3 4 5 6
M1TE (M1 Temporary Enable). This bit controls the temporary assertion of the /M1 signal. It is always read back as a 1 and is set to 1 during reset. When M1E is set to 0 to accommodate certain external Z80 peripheral(s), those same device(s) may require a pulse on M1 after programming certain of their registers to complete the function being programmed.
For example, when a control word is written to the Z80 PIO to enable interrupts, no enable actually takes place until the PIO sees an active M1 signal. When M1TE=1, there is no change in the operation of the /M1 signal and M1E controls its function. When M1TE=0, the M1 output will be asserted during the next opcode fetch cycle regardless of the state programmed into the M1E bit. This is only momentary (one time) and the user need not preprogram a 1 to disable the function (see Figure10).
DS971800401
PRELIMINARY
1-15
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
Zilog
T1
T2
T3
T1
T2
T3
/WR /M1
Write into OMCR Opcode Fetch Figure 10. M1 Temporary Enable Timing
IOC. This bit controls the timing of the /IORQ and /RD signals. It is set to 1 by reset. T1 T2
When /IOC=1, the /IORQ and /RD signals function the same as the Z64180 (Figure 11). TW T3
/IORQ /RD /WR
Figure 11. I/O Read and Write Cycles with IOC = 1
When /IOC = 0, the timing of the /IORQ and RD signals match the timing of the Z80. The /IORQ and /RD signals T1 T2
go active as a result of the rising edge of T2. (Figure 12.)
TW
T3
/IORQ /RD /WR
Figure 12. I/O Read and Write Cycles with IOC = 0
1-16
PRELIMINARY
DS971800401
Zilog HALT and Low-Power Operating Modes. The Z80180/Z8S180/Z8L180 can operate in seven modes with respect to activity and power consumption: - - - - - - - Normal Operation HALT Mode IOSTOP Mode SLEEP Mode SYSTEM STOP Mode IDLE Mode STANDBY Mode (with RECOVERY)
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor HALT Mode. This mode is entered by the HALT instruction. Thereafter, the Z80180/Z8S180/Z8L180 processor continually fetches the following opcode but does not execute it, and drives the HALT, ST and M1 pins all Low. The oscillator and PHI pin remain active, interrupts and bus granting to external masters, and DRAM refresh can occur and all on-chip I/O devices continue to operate including the DMA channels. The Z80180/Z8S180/Z8L180 leaves HALT mode in response to a Low on RESET, on to an interrupt from an enabled on-chip source, an external request on NMI, or an enabled external request on INT0, INT1, or INT2. In case of an interrupt, the return address will be the instruction following the HALT instruction; at that point the program can either branch back to the HALT instruction to wait for another interrupt, or can examine the new state of the system/application and respond appropriately.
1
or
without
QUICK
Normal Operation. The Z80180/Z8S180/Z8L180 processor is fetching and running a program. All enabled functions and portions of the device are active, and the HALT pin is High.
INTi, NMI
A0-A19
HALT Opcode Address
HALT Opcode Address + 1
/HALT
/M1
/MREQ
/RD
Figure 13. HALT Timing
SLEEP Mode. This mode is entered by keeping the IOSTOP bit (ICR5) bits 3 and 6 of the CPU Control Register (CCR3, CCR6) all zero and executing the SLP instruction. The oscillator and PHI output continue operating, but are blocked from the CPU core and DMA channels to reduce power consumption. DRAM refresh stops but interrupts and granting to external master can occur. Except when the bus is granted to an external master, A19-0 and all control signals except /HALT are maintained High. /HALT is Low. I/O operations continue as before the SLP instruction, except for the DMA channels.
The Z80180/Z8S180/Z8L180 leaves SLEEP mode in response to a low on /RESET, an interrupt request from an on-chip source, an external request on /NMI, or an external request on /INT0, 1, or 2.
DS971800401
PRELIMINARY
1-17
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor If an interrupt source is individually disabled, it cannot bring the Z80180/Z8S180/Z8L180 out of SLEEP mode. If an interrupt source is individually enabled, and the IEF bit is 1 so that interrupts are globally enabled (by an EI instruction), the highest priority active interrupt will occur, with the return address being the instruction after the SLP instruction. If an interrupt source is individually enabled, but the IEF bit is 0 so that interrupts are globally disabled (by a DI instruction), the Z80180/Z8S180/Z8L180 leaves
Zilog SLEEP mode by simply executing the following instruction(s). This provides a technique for synchronization with highspeed external events without incurring the latency imposed by an interrupt response sequence. Figure 14 shows the timing for exiting SLEEP mode due to an interrupt request. Note that the Z80180/Z8S180/Z8L180 takes about 1.5 clocks to restart.
SLP 2nd Opcode Fetch Cycle
SLEEP Mode T1 T2 TS TS T1
Opcode Fetch or Interrupt Acknowledge Cycle T2 T3
/INTi, /NMI A0-A19 /HALT M1
T2
T3
SLP 2nd Opcode Address
FFFFFH
Figure 14. SLEEP Timing
IOSTOP Mode. IOSTOP mode is entered by setting the IOSTOP bit of the I/O Control Register (ICR) to 1. In this case, on-chip I/O (ASCI, CSI/O, PRT) stops operating. However, the CPU continues to operate. Recovery from IOSTOP mode is by resetting the IOSTOP bit in ICR to 0. SYSTEM STOP Mode. SYSTEM STOP mode is the combination of SLEEP and IOSTOP modes. SYSTEM STOP mode is entered by setting the IOSTOP bit in ICR to 1 followed by execution of the SLP instruction. In this mode, on-chip I/O and CPU stop operating, reducing power consumption, but the PHI output continues to operate. Recovery from SYSTEM STOP mode is the same as recovery from SLEEP mode except that internal I/O sources (disabled by IOSTOP) cannot generate a recovery interrupt.
IDLE Mode. Software can put the Z80180/Z8S180/Z8L180 into this mode by setting the IOSTOP bit (ICR5) to 1, CCR6 to 0, CCR3 to 1 and executing the SLP instruction. The oscillator keeps operating but its output is blocked to all circuitry including the PHI pin. DRAM refresh and all internal devices stop, but external interrupts can occur. Bus granting to external masters can occur if the BREST bit in the CPU control Register (CCR5) was set to 1 before IDLE mode was entered. The Z80180/Z8S180/Z8L180 leaves IDLE mode in response to a Low on RESET, an external interrupt request on NMI, or an external interrupt request on /INT0, /INT1 or /INT2 that is enabled in the INT/TRAP Control Register. As previously described for SLEEP mode, when the Z80180/Z8S180/Z8L180 leaves IDLE mode due to an NMI, or due to an enabled external interrupt request when the IEF flag is 1 due to an EI instruction, it starts by performing the interrupt with the return address being that of the instruction after the SLP instruction. If an external interrupt enables the INT/TRAP control register while the IEF1 bit is 0, Z80180/Z8S180/Z8L180 leaves IDLE mode; specifically, the processor restarts by executing the instructions following the SLP instruction.
1-18
PRELIMINARY
DS971800401
Zilog Figure 15 shows the timing for exiting IDLE mode due to an interrupt request. Note that the
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor Z80180/Z8S180/Z8L180 takes about 9.5 clocks to restart.
1
IDLE Mode T1 Opcode Fetch or Interrupt Acknowledge Cycle T2 T3 T4
9.5 Cycle Delay from INTi Asserted NMI or INTi
A19-A0
FFFFFH
HALT
M1
Figure 15. Z80180/Z8S180/Z8L180 IDLE Mode Exit due to External Interrupt
While the Z80180/Z8S180/Z8L180 is in IDLE mode, it will grant the bus to an external master if the BREXT bit (CCR5) is 1. Figure 16 shows the timing for this sequence. Note that the part takes 8 clock cycles longer to respond to the Bus Request than in normal operation.
After the external master negates the Bus Request, the Z80180/Z8S180/Z8L180 disables the PHI clock and remains in IDLE mode.
DS971800401
PRELIMINARY
1-19
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor IDLE Mode Bus RELEASE Mode IDLE Mode TX TX
Zilog
9.5 Cycle Delay until BUSACK Asserted BUSREQ
BUSACK
A19-A0 High HALT Low M1
FFFFFH High Impedance
FFFFFH
Figure 16. Bus Granting to External Master in IDLE Mode
STANDBY Mode (With or Without QUICK RECOVERY). Software can put the Z80180/Z8S180/Z8L180 into this mode by setting the IOSTOP bit (ICR5) to 1 and CCR6 to 1, and executing the SLP instruction. This mode stops the on-chip oscillator and thus draws the least power of any mode, less than 10A. As with IDLE mode, the Z80180/Z8S180/Z8L180 will leave STANDBY mode in response to a Low on RESET or on NMI, or a Low on INT0-2 that is enabled by a 1 in the corresponding bit in the INT/TRAP Control Register, and will grant the bus to an external master if the BREXT bit in the CPU Control Register (CCR5) is 1. But the time required for all of these operations is greatly increased by the need to restart the on-chip oscillator and ensure that it has stabilized to square-wave operation. When an external clock is connected to the EXTAL pin rather than a crystal to the XTAL and EXTAL pins, and the external clock runs continuously, there is little need to use STANDBY mode because there is no time required to restart the oscillator, and other modes restart faster. However, if external logic stops the clock during STANDBY mode (for example, by decoding HALT Low and M1 High for several clock cycles), then STANDBY mode can be useful to allow the external clock source to stabilize after it is re-enabled. When external logic drives RESET Low to being a Z80180/Z8S180/Z8L180 out of STANDBY mode, and a 1-20
crystal is used or an external clock source has been stopped, the external logic must hold RESET Low until the on-chip oscillator or external clock source has restarted and stabilized. The clock stability requirements of the Z80180/Z8S180/Z8L180 are much less in the divide-bytwo mode that's selected by a Reset sequence and thereafter controlled by the Clock Divide bit in the CPU Control Register (CCR7). Because of this, software should: a. Program CCR7 to 0 to select divide-by-two mode, before the SLP instruction that enters STANDBY mode, and. b. After a Reset, interrupt or in-line restart after the SLP 01 instruction, delay programming CCR7 back to 1 to set divide-by-one mode, as long as possible to allow additional clock stabilization time. If software sets CCR6 to 1 before the SLP instruction places the MPU in STANDBY mode, the value in the CCR3 bit determines how long the Z80180/Z8S180/Z8L180 will wait for oscillator restart and stabilization when it leaves STANDBY mode due to an external interrupt request. If CCR3 is 0, the Z80180/Z8S180/Z8L180 waits 217 (131,072) clock cycles, while if CCR3 is 1, it waits only 64 clock cycles. The latter is called QUICK RECOVERY mode. The same delay applies to granting the bus to an DS971800401
PRELIMINARY
Zilog external master during STANDBY mode, when the BREXT bit in the CPU Control Register (CCR5) is 1. As described previously for SLEEP and IDLE modes, when a Z80180/Z8S180/Z8L180 leaves STANDBY mode due to NMI Low, or when it leaves STANDBY mode due to an enabled INTO-2 low when the IEF, flag is 1 due to an IE instruction, it starts by performing the interrupt with the return address being that of the instruction following the SLP instruction. If the Z80180/Z8S180/Z8L180 leaves STANDBY mode due to an external interrupt request that's
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor enabled in the INT/TRAP Control Register, but the IEF, bit is 0 due to a DI instruction, the processor restarts by executing the instruction(s) following the SLP instruction. If INT0, or INT1 or 2 goes inactive before the end of the clock stabilization delay, the Z80180/Z8S180/Z8L180 stays in STANDBY mode. Figure 17 shows the timing for leaving STANDBY mode due to an interrupt request. Note that the Z80180/Z8S180/Z8L180 takes either 64 or 217 (131,072) clocks to restart, depending on the CCR3 bit. Opcode Fetch or Interrupt Acknowledge Cycle T1 T2 T3 T4
1
STANDBY Mode
217 or 64 Cycle Delay from INTi Asserted NMI or INTi
A19-A0
FFFFFH
HALT
M1
Figure 17. Z80180/Z8S180/Z8L180 STANDBY Mode Exit due to External Interrupt
While the Z80180/Z8S180/Z8L180 is in STANDBY mode, it will grant the bus to an external master if the BREXT bit (CCR5) is 1. Figure 18 shows the timing of this sequence. Note that the part takes 64 or 217 (131,072) clock cycles to grant the bus depending on the CCR3 bit.
The latter (non-Quick-Recovery) case may be prohibitive for many "demand driven" external masters. If so, QUICK RECOVERY or IDLE mode can be used.
DS971800401
PRELIMINARY
1-21
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor STANDBY Mode Bus Release Mode TX TX STANDBY Mode
Zilog
64 or 217 Cycle Delay after BUSREQ Asserted BUSREQ
BUSACK
A19-A0 Low HALT High M1
FFFFFH
FFFFFH
Figure 18. Bus Granting to External Master During STANDBY Mode
1-22
PRELIMINARY
DS971800401
Zilog
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
STANDARD TEST CONDITIONS
The DC Characteristics and Capacitance sections above apply to the following standard test conditions, unless otherwise noted. All voltages are referenced to GND (0V). Positive current flows in to the referenced pin. All AC parameters assume a load capacitance of 100 pF. Add 10 ns delay for each 50 pF increase in load up to a maximum of 200 pF for the data bus and 100 pF for the address and control lines. AC timing measurements are referenced to 1.5 volts (except for CLOCK, which is referenced to the 10% and 90% points). The Ordering Information section lists temperature ranges and product numbers. Package drawings are in the Package Information section. Refer to the Literature List for additional documentation.
From Output Under Test +5 V 2.1k
1
100 pF
250 A
Figure 19. AC Load Capacitance Parameters
ABSOLUTE MAXIMUM RATINGS
Item Supply Voltage Input Voltage Operating Temperature Extended Temperature Storage Temperature Symbol Vcc Vin Topr Text Tstg Value -0.3 ~ +7.0 -0.3 ~ Vcc +0.3 0 ~ 70 -40 ~ 85 -55 ~ +150 Unit V V C C C
Note: Permanent LSI damage may occur if maximum ratings are exceeded. Normal operation should be under recommended operating conditions. If these conditions are exceeded, it could affect reliability of LSI.
DS971800401
PRELIMINARY
1-23
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
Zilog
DC CHARACTERISTICS
Note: Vcc = 5V + 10%, V ss = 0V over specified temperature range unless otherwise noted. Symbol VIH1 VIH2 VIH3 VIL1 VIL2 VOH VOL IIL Item Input "H" Voltage /RESET, EXTAL, /NMI Input "H" Voltage Except /RESET, EXTAL, /NMI Input "H" Voltage Except CKS, CKA0, CKA1 Input "L" Voltage /RESET, EXTAL, /NMI Input "L" Voltage Except /RESET, EXTAL, /NMI Outputs "H" Voltage All outputs Outputs "L" Voltage All outputs Input Leakage Current All Inputs Except XTAL, EXTAL Three State Leakage Current Power Dissipation* (Normal Operation) Power Dissipation* (SYSTEM STOP mode) CP Pin Capacitance Condition Min. Vcc -0.6 2.0 2.4 -0.3 -0.3 IOH = -200 A IOH = -20 A IOL = -2.2 A VIN = 0.5 ~ Vcc -0.5 2.4 Vcc -1.2 - - Typ. - - - - - - - - - Max. Vcc +0.3 Vcc +0.3 Vcc +0.3 0.6 0.8 - - 0.45 1.0 V A A MA Unit V V V V V V
ITL ICC*
VIN = 0.5 ~ Vcc -0.5 F = 6 MHz F = 8 MHz F = 10 MHz** F = 6 MHz F = 8 MHz F = 10 MHz** VIN = 0V, f = 1 MHz Ta = 25 C
- - - - - - - -
- 15 20 25 3.8 5 6.3 -
1.0 40 50 60 12.5 15 17.5 12
pF
Note: ** VIHmin = VCC -1.0V, VILmax = 0.8V (all output terminals are at no load.) VCC = 5.0V
1-24
PRELIMINARY
DS971800401
Zilog
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
AC CHARACTERISTICS
Vcc = 5V + 10%, V ss = 0V, TA - 0 to +70 C, unless otherwise noted.
Z80180-6 No. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 26a. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. Symbol Item tcyc tCHW tCLW tcf tcr tAD tAS tMED1 tRDD1 tM1D1 tAH tMED2 tRDD2 tM1D2 tDRS tDRH tSTD1 tSTD2 tWS tWH tWDZ tWRD1 tWDD tWDS tWRD2 tWRP tWDH tIOD1 tIOD2 tIOD3 tINTS tINTS tNMIW tBRS tBRH tBAD1 tBAD2 tBZD Clock Cycle Time Clock "H" Pulse Width Clock "L" Pulse Width Clock Fall Time Clock Rise Time ORise to Address Valid Delay Address Valid to /MREQ Fall or /IORQ Fall) O Fall to /MREQ Fall Delay O Fall to /RD Fall Delay O Rise to /RD Rise Delay O Rise to /M1 Fall Delay Address Hold Time from (/MREQ, /IOREQ, /RD, /WR) O Fall to /MREQ Rise Delay O Fall to /RD Rise Delay O Rise to /M1 Rise Delay Data Read Set-up Time Data Read Hold Time O Fall to ST Fall Delay O Fall to ST Rise Delay /WAIT Set-up Time to O Fall /WAIT Hold Time from O Fall O Rise to Data Float Delay O Rise to /WR Fall Delay O Fall to Write Data Delay Time Write Data Set-up Time to /WR Fall O Fall to /WR Rise Delay /WR Pulse Width /WR Pulse Width (I/O Write Cycle) Write Data Hold Time from (/WR Rise) O Fall to /IORQ Fall Delay O Rise to /IORQ Fall Delay O Fall to /IORQ Rise Delay /M1 Fall to /IORQ Fall Delay /INT Set-up Time to O Fall /INT Hold Time from O Fall /NMI Pulse Width /BUSREQ Set-up Time to O Fall /BUSREQ Hold Time from O Fall O Rise to /BUSACK Fall Delay O Fall to /BUSACK Rise Delay O Rise to Bus Floating Delay Time /IOC = 1 /IOC = 1 /IOC = 1 /IOC = 0 Min. 162 65 65 - - - 30 - - - - 35 - - - 40 0 - - 40 40 - - - 40 - 170 332 40 - - - 340 40 40 120 40 40 - - - 110 Max. 2000 - - 15 15 90 - 60 60 65 80 - 60 60 80 - - 90 90 - - 95 65 90 - 80 - - - 60 65 60 - - - - - - 95 90 125 - Z80180-8 Min. 125 50 50 - - - 20 - - - - 20 - - - 30 0 - - 40 40 - - - 20 - 130 255 15 - - - 250 40 40 100 40 40 - - - 90 70 70 90 - Max. 2000 - - 15 15 80 - 50 50 60 70 - 50 50 70* - - 70 70 - - 70 60 80 - 60 - - - 50 60 50 - - - - - Z80180-10 Min. 100 40 40 - - - 10 - - - - 10 - - - 25 0 - - 30 30 - - - 15 - 110 210 10 - - - 200 30 30 80 30 30 - - - 70 60 60 80 - Max. 2000 - - 10 10 70 - 50 50 55 60 - 50 50 60 - - 60 60 - - 60 50 60 - 50 - - - 50 55 50 - - - - - ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns Unit ns ns ns ns ns ns ns ns ns
1
tMEWH /MREQ Pulse Width (HIGH)
DS971800401
PRELIMINARY
1-25
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
Z80180-6 No. 40. 41. 42. 43. 44. 45. 46. 47. 48. 49. 50. 51. 52. 53. 54. 55. 56. 57. 58. 59. 60. 61. 62. 63. 64. 65. 66. 67. 68. 69. 70. Symbol Item tMEWL tRFD1 tRFD2 tHAD1 tHAD2 tDRQS tDRQH tTED1 tTED2 tED1 tED2 PWEH PWEL tEr tEf tTOD tSTDI tSTDE tSRSI tSRHI tSRSE tSRHE tRES tREH tOSC tEXr tEXf tRr tRf tIr tIf /MREQ Pulse Width (LOW) O Rise to /RFSH Fall Delay O Rise to /RFSH Rise Delay O Rise to /HALT Fall Delay O Rise to /HALT Rise Delay /DREQi Set-up Time to O Rise /DREQi Hold Time from O Rise O Fall to /TENDi Fall Delay O Fall to /TENDI Rise Delay O Rise to E Rise Delay O Fall or Rise to E Fall Delay E Pulse Width (HIGH) E Pulse Width (LOW) Enable Rise Time Enable Fall Time O Fall to Timer Output Delay CSI/O Transmit Data Delay Time (Internal Clock Operation) CSI/O Transmit Data Delay Time (External Clock Operation) CSI/O Receive Data Set-up Time (Internal Clock Operation) CSI/O Receive Data Hold Time (Internal Clock Operation) CSI/O Receive Data Set-up Time (External Clock Operation) CSI/O Receive Data Hold Time (External Clock Operation) /RESET Set-up Time to O Fall /RESET Hold Time from O Fall Oscillator Stabilization Time External Clock Rise Time (EXTAL) External Clock Fall Time (EXTAL) /RESET Rise Time /RESET Fall Time Input Rise Time (except EXTAL, /RESET) Input Fall Time (except EXTAL, /RESET) Min. 125 - - - - 40 40 - - - - 75 180 - - - - - 1 1 1 1 120 80 - - - - - - - Max. - 90 90 90 90 - - 70 70 95 95 - - 20 20 300 200 7.5tcyc +300 - - - - - - 20 25 25 50 50 100 100 Z80180-8 Min. 100 - - - - 40 40 - - - - 65 130 - - - - - 1 1 1 1 100 70 - - - - - - - Max. - 80 80 80 80 - - 60 60 70 70 - - 20 20 200 200 7.5tcyc +200 - - - - - - 20 25 25 50 50 100 100 Z80180-10 Min. 80 - - - - 30 30 - - - - 55 110 - - - - - 1 1 1 1 80 50 - - - - - - - Max. - 60 60 50 50 - - 50 50 60 60 - - 20 20 150 150 7.5tcyc +150 - - - - - - TBD 25 25 50 50 100 100
Zilog
Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns tcyc tcyc tcyc tcyc ns ns ns ns ns ns ns ns ns
1-26
PRELIMINARY
DS971800401
Zilog
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
AC CHARACTERISTICS (VCC = 5V 10% or VCC = 3.3V 10% over specified temperature range, unless otherwise noted, 33 MHZ characteristics apply only to 5V operation.)
Z80180-20 No. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 26a. 27. 28. 29. 30. 31. 32. 33. 34. 35. 36. 37. Symbol tcyc tCHW tCLW tcf tcr tAD tAS tMED1 tRDD1 tM1D1 tAH tMED2 tRDD2 tM1D2 tDRS tDRH tSTD1 tSTD2 tWS tWH tWDZ tWRD1 tWDD tWDS tWRD2 tWRP tWDH tIOD1 tIOD2 tIOD3 tINTS tINTS tNMIW tBRS tBRH tBAD1 tBAD2 Item Clock Cycle Time Clock "H" Pulse Width Clock "L" Pulse Width Clock Fall Time Clock Rise Time ORise to Address Valid Delay Address Valid to /MREQ Fall or /IORQ Fall) O Fall to /MREQ Fall Delay O Fall to /RD Fall Delay O Rise to /RD Rise Delay O Rise to /M1 Fall Delay Address Hold Time from (/MREQ, /IOREQ, /RD, /WR) O Fall to /MREQ Rise Delay O Fall to /RD Rise Delay O Rise to /M1 Rise Delay Data Read Set-up Time Data Read Hold Time O Fall to ST Fall Delay O Fall to ST Rise Delay /WAIT Set-up Time to O Fall /WAIT Hold Time from O Fall O Rise to Data Float Delay O Rise to /WR Fall Delay O Fall to Write Data Delay Time Write Data Set-up Time to /WR Fall O Fall to /WR Rise Delay /WR Pulse Width /WR Pulse Width (I/O Write Cycle) Write Data Hold Time from (/WR Rise) O Fall to /IORQ Fall Delay O Rise to /IORQ Fall Delay O Fall to /IORQ Rise Delay /M1 Fall to /IORQ Fall Delay /INT Set-up Time to O Fall /INT Hold Time from O Fall /NMI Pulse Width /BUSREQ Set-up Time to O Fall /BUSREQ Hold Time from O Fall O Rise to /BUSACK Fall Delay O Fall to /BUSACK Rise Delay /IOC = 1 /IOC = 1 /IOC = 1 /IOC = 0 Min. 50 15 15 - - - 20 - - - - - - - - 15 0 - - 15 5 - - - 10 - 70 120 5 - - - 120 15 10 35 10 10 - - Max. 2000 - - 10 10 15 - 15 15 15 15 20 15 15 15 - - 15 15 - - 10 15 20 - 15 - - - 15 15 15 - - - - - - 15 15 Z80180-33 Min. 33 10 10 - - - 5 - - - - 5 - - - 15 0 - - 15 5 - - - 0 - 40 70 5 - - - 70 15 10 25 10 10 - - 15 15 Max. 2000 - - 5 5 15 - 15 15 15 15 - 15 15 15* - - 15 15 - - 10 15 20 - 15 - - - 15 15 15 - - - - - ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns Unit ns ns ns ns ns ns ns ns ns
1
DS971800401
PRELIMINARY
1-27
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
Z80180-20 No. 38. 39. 40. 41. 42. 43. 44. 45. 46. 47. 48. 49. 50. 51. 52. 53. 54. 55. 56. 57. 58. 59. 60. 61. 62. 63. 64. 65. 66. 67. 68. 69. 70. Symbol tBZD tMEWH tMEWL tRFD1 tRFD2 tHAD1 tHAD2 tDRQS tDRQH tTED1 tTED2 tED1 tED2 PWEH PWEL tEr tEf tTOD tSTDI tSTDE tSRSI tSRHI tSRSE tSRHE tRES tREH tOSC tEXr tEXf tRr tRf tIr tIf Item O Rise to Bus Floating Delay Time /MREQ Pulse Width (HIGH) /MREQ Pulse Width (LOW) O Rise to /RFSH Fall Delay O Rise to /RFSH Rise Delay O Rise to /HALT Fall Delay O Rise to /HALT Rise Delay /DREQi Set-up Time to O Rise /DREQi Hold Time from O Rise O Fall to /TENDi Fall Delay O Fall to /TENDI Rise Delay O Rise to E Rise Delay O Fall or Rise to E Fall Delay E Pulse Width (HIGH) E Pulse Width (LOW) Enable Rise Time Enable Fall Time O Fall to Timer Output Delay CSI/O Transmit Data Delay Time (Internal Clock Operation) CSI/O Transmit Data Delay Time (External Clock Operation) CSI/O Receive Data Set-up Time (Internal Clock Operation) CSI/O Receive Data Hold Time (Internal Clock Operation) CSI/O Receive Data Set-up Time (External Clock Operation) CSI/O Receive Data Hold Time (External Clock Operation) /RESET Set-up Time to O Fall /RESET Hold Time from O Fall Oscillator Stabilization Time External Clock Rise Time (EXTAL) External Clock Fall Time (EXTAL) /RESET Rise Time /RESET Fall Time Input Rise Time (except EXTAL, /RESET) Input Fall Time (except EXTAL, /RESET) Min. - 45 45 - - - - 20 15 - - - - 45 70 - - - - - 1 1 1 1 25 15 - - - - - - - Max. 10 - - 15 15 15 15 - - 15 15 15 15 - - 10 10 50 2 7.5tcyc +75 - - - - - - 20 10 10 50 50 50 50 Z80180-33 Min. - 25 25 - - - - 20 15 - - - - 20 20 - - - - - 1 1 1 1 25 15 - - - - - - - Max. 25 - - 15 15 15 15 - - 15 15 15 15 - - 10 10 50 2 7.5tcyc +60 - - - - - - 20 5 5 50 50 50 50
Zilog
Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns tcyc tcyc tcyc tcyc ns ns ns ns ns ns ns ns ns
1-28
PRELIMINARY
DS971800401
Zilog
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
TIMING DIAGRAMS
Opcode fetch Cycle T1 2
o
T2 3 5
TW
T3
T1
I/O Write Cycle *2 I/O Read Cycle *2 T2 TW T3
T1
1
4 1 6
ADDRESS 19 /WAIT 7 12 11 20 19 20
/MREQ
8 /IORQ 11 13 /RD 9 9 /WR 14 /M1 10 ST 17 15 Data IN Data OUT 62 /RESET 68 67 63 62 63 23 16 15 24 16 21 18 22 25 11 28 13 7 29 11
27
*1
67
68
Notes:
*1. Output buffer is off at this point. *2. Memory Read/Write Cycle timing are the same as I/O Read/Write Cycle except there are no automatic wait states (TW), and /MREQ is active instead of /IORQ.
Figure 20. CPU Timing (Opcode Fetch Cycle, Memory Read Cycle, Memory Write Cycle, I/O Write Cycle, I/O Read Cycle)
DS971800401
PRELIMINARY
1-29
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
Zilog
o
/INTi
31
32
33 /NMI
/MI *1 10 /IORQ *1 30 28 15 Date IN *1 39 /MREQ *2 41 /RFSH *2 34 /BUSREQ 36 /BUSACk 38 ADDRESS DATA /MREQ /RD /WR, /IORQ 43 /HALT
*3
14
29 16
40
42
35
34
35
37
38
44
Notes:
1. During /INT0 acknowledge cycle. 2. During refresh cycle. 3. Output buffer is off at this point.
Figure 21. CPU Timing (/INT0 Acknowledge Cycle, Refresh Cycle, BUS RELEASE Mode, HALT Mode, SLEEP Mode, SYSTEM STOP Mode)
1-30
PRELIMINARY
DS971800401
Zilog
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
I/O Read Cycle T1
I/O Write Cycle T1 T2 Tw T3
T2
Tw
T3
1
ADDRESS 28 IROQ 9 RD
13
29
28
29
22
25
WR
CPU Timing (IOC=0)
I/O Read Cycle I/O Write Cycle
Figure 22. CPU Timing (/IOC = 0) (I/O Read Cycle, I/O Write Cycle)
T1
o
CPU or DMA Read/Write Cycle (Only DMA Write Cycle for /TENDi) T2 TW T3 T1
45 /DREQi (at level sense)
*2
*1 46
45 46 /DREQi (at level sense)
47 48 /TENDi ST
*3
*4
18
17
1. *2. *3. *4.
tDRQS and tDHQH are specified for the rising edge of clock followed by T3. tDRQS and tDHQH are specified for the rising edge of clock. DMA cycle starts. CPU cycle starts
Figure 23. DMA Control Signals
DS971800401
PRELIMINARY
1-31
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
T1 o T2 TW TW T3
Zilog
~~ ~~
49 E
50
(Memory Read//Write)
49 50
~ ~
E (I/O Read) 49 50
~ ~
E (I/O Write)
15
16
~~ ~~
D0 - D7
Figure 24. E Clock Timing (Memory Read/Write Cycle, I/O Read/Write Cycle)
o E BUS RELEASE mode SLEEP mode SYSTEM STOP mode 49 50
Figure 25. E Clock Timing (BUS RELEASE Mode, SLEEP Mode, SYSTEM STOP Mode)
T2
TW
T3 50
T1
T2 49
E Example I/O read Opcode fetch
52
50 49 51 54 53
53
54
Figure 26. E Clock Timing (Minimum timing example of PWEL and PWEH)
1-32
PRELIMINARY
DS971800401
Zilog
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
Timer Data Reg.=0000H
1
A18/TOUT 55
Figure 27. Timer Output Timing
SLP Instruction fetch T3 o T1 T2 TS TS
Next Opcode fetch T1 T2
~ ~
31
32
~ ~
/INTi
~ ~
/NMI
33
~~~ ~~~
A0 ~ A18
/MREQ, /MI /RD /HALT
43 44
Figure 28. SLP Execution Cycle
~ ~
DS971800401
PRELIMINARY
1-33
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
Zilog
CSI/O CLock
56
56
Transmit data (Internal Clock) 57 Transmit data (External Clock) 11tcyc 58 Receive data (Internal Clock) 11.5tcyc Receive data (External Clock) 16.5tcyc 11.5tcyc 16.5tcyc 59 11tcyc 58 59 57
60
61
60
61
Figure 29. CSI/O Receive/Transmit Timing
65 EXTAL VIL1 VIH1 VIH1
66 VIL1
70
69
Input Rise Time and Fall Time (Except EXTAL, /RESET)
External Clock Rise Time and Fall Time
Figure 30. Rise Time and Fall Times
1-34
PRELIMINARY
DS971800401
Zilog
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
CPU CONTROL REGISTER
CPU Control Register (CCR). This register controls the basic clock rate, certain aspects of Power-Down modes, and output drive/low noise options (Figure 31).
1
CPU Control Register (CCR) D7 D6 D5 D4 D3 D2 D1 D0 Clock Divide 0 = XTAL/2 1 = XTAL/1 STANDBY/IDLE Enable 00 = No STANDBY 01 = IDLE After SLEEP 10 = STANDBY After SLEEP 11 = STANDBY After SLEEP 64-Cycle Exit (QUICK RECOVERY) BREXT 0 = Ignore BUSREQ on STANDBY/IDLE 1 = STANDBY/IDLE Exit on BUSREQ LNAD/DATA 0 = Standard Drive 1 = 33% Drive on A19-A0, D7-D0 LNCPUCTL 0 = Standard Drive 1 = 33% Drive on CPU Control Signals LNIO 0 = Standard Drive 1 = 33% Drive on Group 1 I/O Signals LNPHI 0 = Standard Drive 1 = 33% Drive on PHI Pin
Figure 31. CPU Control Register (CCR) Address 1FH
Bit 7. Clock Divide Select. If this bit is 0, as it is after a Reset, the Z80180/Z8S180/Z8L180 divides the frequency on the XTAL pin(s) by two to obtain its master clock PHI. If this bit is programmed as 1, the part uses the XTAL frequency as PHI without division. If an external oscillator is used in divide-by-one mode, the minimum pulse width requirement given in the AC Characteristics must be satisfied. Bits 6 and 3. STANDBY/IDLE Control. When these bits are both 0, a SLP instruction makes the Z80180/Z8S180/Z8L180 enter SLEEP or SYSTEM STOP mode, depending on the IOSTOP bit (ICR5). When D6 is 0 and D3 is 1, setting the IOSTOP bit (ICR5) and executing a SLP instruction puts the Z80180/Z8S180/Z8L180 into IDLE mode in which the onchip oscillator runs, but its output is blocked from the rest of the part, including PHI out. When D6 is 1 and D3 is 0, setting IOSTOP (ICR5) and executing a SLP instruction puts the part into STANDBY mode, in which the on-chip oscillator is stopped and the part allows 217 (128K) clock cycles for the oscillator to stabilize when it's restarted.
When D6 and D3 are both 1, setting IOSTOP (ICR5) and executing a SLP instruction puts the part into QUICK RECOVERY STANDBY mode, in which the on-chip oscillator is stopped, and the part allows only 64 clock cycles for the oscillator to stabilize when it's restarted. The latter section, HALT and LoW POWER Modes, describes the subject more fully. Bit 5 BREXT. This bit controls the ability of the Z8S180/Z8L180 to honor a bus request during STANDBY mode. If this bit is set to 1 and the part is in STANDBY mode, a BUSREQ is honored after the clock stabilization timer is timed out. Bit 4 LNPHI. This bit controls the drive capability on the PHI Clock output. If this bit is set to 1, the PHI Clock output will be reduced to 33 percent of its drive capability.
DS971800401
PRELIMINARY
1-35
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor Bit 2 LNIO. This bit controls the drive capability of certain external I/O pins of the Z8S180/Z8L180. When this bit is set to 1, the output drive capability of the following pins is reduced to 33percent of the original drive capability: - /RTSO/TxS - CKA1 - CKAO - TXAO - TXAI - TOUT Bit 1 LNCPUCTL. This bit controls the drive capability of the CPU Control pins. When this bit is set to 1, the output drive capability of the following pins is reduced to 33percent the original drive capability: - - - - - - - - /BUSACK /RD /WR /M1 /MREQ /IORQ /RFSH /HALT
Zilog Bit 0 LNAD/DATA. This bit controls the drive capability of the Address/Data bus output drivers. If this bit is set to 1, the output drive capability of the Address and Data bus output is reduced to 33percent of its original drive capability.
1-36
PRELIMINARY
DS971800401
Zilog
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
IASCI REGISTER DESCRIPTION
Internal Address/Data Bus Interrupt Request ASCI Transmit Data Register Ch 0: TDR0 TXA0 ASCI Transmit Shift Register* Ch 0: TSR0 ASCI Receive Data FIFO Ch 0: RDR0 RXA0 ASCI Receive Shift Register* Ch 0: RSR0 (8) ASCI Control Register A Ch 0: CNTLA0 (8) ASCI Control Register B Ch 0: CNTB0 (8) ASCI Status FIFO Ch 0 DCD0 ASCI Status Register Ch 0: STAT0 (8) ASCI Extension Control Reg. Ch 0: ASEXT0 (7) ASCI Time Constant Low Ch 0: ASTCOL (8) ASCI Time Constant High Ch 0: ASTCOH (8) ASCI Control ASCI Transmit Data Register Ch 1: TDR1 ASCI Transmit Shift Register* Ch 1: TSR1 ASCI Receive Data FIFO Ch 1: RDR1 ASCI Receive Shift Register* Ch 1: RSR1 (8) ASCI Control Register A Ch 1: CNTLA1 (8) ASCI Control Register B Ch 1: CNTB1 (8) ASCI Status FIFO Ch 1 ASCI Status Register Ch 1: STAT1 (8) ASCI Extension Control Reg. Ch 1: ASEXT1 (5) ASCI Time Constant Low Ch 1: ASTCIL (8) ASCI Time Constant High Ch 1: ASTCIH (8) RXA1 TXA1
1
RTS0 CTS0
CTS1
Note: *Not Program Accessible. CKA0 CKA1 Baud Rate Generator 0 Baud Rate Generator 1
Figure 32. ASCI Block Diagram
DS971800401
PRELIMINARY
1-37
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor The following paragraphs explain the various functions of the ASCI registers. ASCI Transmit Register 0. When the ASCI Transmit Register receives data from the ASCI Transmit Data Register (TDR), the data is shifted out to the TxA pin. When transmission is completed, the next byte (if available) is automatically loaded from TDR into TSR and the next transmission starts. If no data is available for transmission, TSR IDLEs by outputting a continuous High level. This register is not program accessible ASCI Transmit Data Register 0,1 (TDR0, 1: I/O address = 06H, 07H). Data written to the ASCI Transmit Data Register is transferred to the TSR as soon as TSR is empty. Data can be written while TSR is shifting out the previous byte of data. Thus, the ASCI transmitter is double buffered. Data can be written into and read from the ASCI Transmit Data Register. If data is read from the ASCI Transmit Data
Zilog Register, the ASCI data transmit operation will not be affected by this read operation ASCI Receive Shift Register 0,1 (RSR0,1). This register receives data shifted in on the RxA pin. When full, data is automatically transferred to the ASCI Receive Data Register (RDR) if it is empty. If RSR is not empty when the next incoming data byte is shifted in, an overrun error occurs. This register is not program accessible. ASCI Receive Data FIFO 0,1 (RDR0, 1:I/O Address = 08H, 09H). The ASCI Receive Data Register is a read-only register. When a complete incoming data byte is assembled in RSR, it is automatically transferred to the 4 character Receive Data First-In First-Out (FIFO) memory. The oldest character in the FIFO (if any) can be read from the Receive Data Register (RDR). The next incoming data byte can be shifted into RSR while the FIFO is full. Thus, the ASCI receiver is well buffered.
ASCI STATUS FIFO
This 4 entry FIFO contains Parity Error, Framing Error, Rx Overrun, and Break status bits associated with each character in the receive data FIFO. The status of the oldest character (if any) can be read from the ASCI status registers as described below
1-38
PRELIMINARY
DS971800401
Zilog
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
ASCI CHANNEL CONTROL REGISTER A
ASCI Control Register A 0 (CNTLA0: I/O Address = 00H) Bit 7 MPE R/W 6 RE R/W 5 TE R/W 4 RTS0 R/W 3 MPBR/ EFR R/W 2 MOD2 R/W 1 MOD1 R/W 0 MOD0 R/W
1
ASCI Control Register A 1 (CNTLA1: I/O Address = 01H) Bit 7 MPE R/W 6 RE R/W 5 TE R/W 4 CKA1D R/W 3 MPBR/ EFR R/W 2 MOD2 R/W 1 MOD1 R/W 0 MOD0 R/W
Figure 33. ASCI Channel Control Register A
MPE: Multi-Processor Mode Enable (bit 7). The ASCI has a multiprocessor communication mode that utilizes an extra data bit for selective communication when a number of processors share a common serial bus. Multiprocessor data format is selected when the MP bit in CNTLB is set to 1. If multiprocessor mode is not selected (MP bit in CNTLB = 0), MPE has no effect. If multiprocessor mode is selected, MPE enables or disables the "wake-up" feature as follows. If MBE is set to 1, only received bytes in which the MPB (multiprocessor bit) = 1 can affect the RDRF and error flags. Effectively, other bytes (with MPB = 0) are "ignored" by the ASCI. If MPE is reset to 0, all bytes, regardless of the state of the MPB data bit, affect the REDR and error flags. MPE is cleared to 0 during RESET. RE: Receiver Enable (bit 6). When RE is set to 1, the ASCI transmitter is enabled. When TE is reset to 0, the transmitter is disables and any transmit operation in progress is interrupted. However, the TDRE flag is not reset and the previous contents of TDRE are held. TE is cleared to 0 in IOSTOP mode during RESET. TE: Transmitter Enable (bit 5). When TE is set to 1, the ASCI receiver is enabled. When TE is reset to 0, the transmitter is disabled and any transmit operation in progress is interrupted. However, the TDRE flag is not reset and the previous contents of TDRE are held. TE is cleared to 0 in IOSTOP mode during RESET.
RTS0: Request to Send Channel 0 (bit 4 in CNTLA0 only). If bit 4 of the System Configuration Register is 0, the RTS0/TxS pin has the RTS0 function. RTS0 allows the ASCI to control (start/stop) another communication devices transmission (for example, by connecting to that device's CTS input). RTS0 is essentially a 1 bit output port, having no side effects on other ASCI registers or flags. Bit 4 in CNTLA1 is used. CKA1D = 1, CKA1/TEND0 pin = TEND0 CKA1D = 0, CKA1/TEND0 pin = CKA1 Cleared to 0 on reset. MPBR/EFR: Multiprocessor Bit Receive/Error Flag Reset (bit 3). When multiprocessor mode is enabled (MP in CNTLB = 1), MPBR, when read, contains the value of the MPB bit for the last receive operation. When written to 0, the EFR function is selected to reset all error flags (OVRN, FE, PE and BRK in the ASEXT Register) to 0. MPBR/EFR is undefined during RESET.
DS971800401
PRELIMINARY
1-39
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor MOD2, 1, 0: ASCI Data Format Mode 2, 1, 0 (bits 2-0). These bits program the ASCI data format as follows. MOD2 = 07 bit data = 18 bit data MOD1 = 0No parity = 1Parity enabled MOD0 = 01 stop bit = 12 stop bits
Zilog The data formats available based on all combinations of MOD2, MOD1, and MOD0 are shown in Table 5-6. Table 5. Data Formats MOD2 MOD1 MOD0 Data Format 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 Start + 7 bit data + 1 stop Start + 7 bit data + 2 stop Start + 7 bit data + parity + 1 stop Start + 7 bit data + parity + 2 stop Start + 8 bit data + 1 stop Start + 8 bit data + 2 stop Start + 8 bit data + parity + 1 stop Start + 8 bit data + parity + 2 stop
ASCI CHANNEL CONTROL REGISTER B
ASCI Control Register B 0 (CNTLB0: I/O Address = 02H) ASCI Control Register B 1 (CNTLB1: I/O Address = 03H) Bit 7 MPBT R/W 6 MP R/W 5 CTS/ PS R/W 4 PEO R/W 3 DR R/W 2 SS2 R/W 1 SS1 R/W 0 SS0 R/W
Figure 34. ASCI Channel Control Register B
MPBT: Multiprocessor Bit Transmit (bit 7). When multiprocessor communication format is selected (MP bit = 1), MPBT is used to specify the MPB data bit for transmission. If MPBT = 1, then MPB = 1 is transmitted. If MPBT = 0, then MPB = 0 is transmitted. MPBT state is undefined during and after RESET. MP: Multiprocessor Mode (bit 6). When MP is set to 1, the data format is configured for multiprocessor mode based on the MOD2 (number of data bits) and MOD0 (number of stop bits) bits in CNTLA. The format is as follows. Start bit + 7 or 8 data bits + MPB bit + 1 or 2 stop bits Note that multiprocessor (MP=1) format has no provision for parity. If MP = 0, the data format is based on MOD0, MOD1, MOD2, and may include parity. The MP bit is cleared to 0 during RESET. CTS/PS: Clear to Send/Prescale (bit 5). When read, /CTS/PS reflects the state of the external /CTS input. If the /CTS input pin is HIGH, /CTS/PS will be read as 1. Note that when the /CTS input pin is HIGH, the TDRE bit is inhibited (i.e. held at 0). For channel 1, the /CTS input is multiplexed with RXS pin (Clocked Serial Receive Data). 1-40
Thus, /CTS/PS is only valid when read if the channel 1 CTS1E bit = 1 and the /CTS input pin function is selected. The read data of /CTS/PS is not affected by RESET. If the SS2-0 bits in this register are not 111, and the BRG mode bit in the ASEXT register is 0, then writing to this bit sets the prescale (PS) control as described in the following "Clock Modes" section. Under those circumstances, a 0 indicates a divide by 10 prescale function while a 1 indicates divide by 30. The bit resets to 0. PEO: Parity Even Odd (bit 4). PEO selects oven or odd parity. PEO does not affect the enabling/disabling of parity (MOD1 bit of CNTLA). If PEO is cleared to 0, even parity is selected. If PEO is set to 1, odd parity is selected. PEO is cleared to 0 during RESET. DR: Divide Ratio (bit 3). If the X1 bit in the ASEXT register is 0, this bit specifies the divider used to obtain baud rate from the data sampling clock. If DR is reset to 0, divide- by-16 is used, while if DR is set to 1 divide-by-64 is used. DR is cleared to 0 during RESET. SS2,1,0: Source/Speed Select 2,1,0 (bits 2-0). First, if these bits are 111, as they are after a Reset, the CKA pin
PRELIMINARY
DS971800401
Zilog is used as a clock input, and is divided by 1, 16, or 64 depending on the DR bit and the X1 bit in the ASEXT register. If these bits are not 111 and the BRG mode bit is ASEXT is 0, then these bits specify a power-of-two divider for the PHI clock as shown in Table 9. Setting or leaving these bits as 111 makes sense for a channel only when its CKA pin is selected for the CKA function. CKAO/CKS has the CKAO function when bit 4 of the System Configuration Register is 0. DCD0/CKA1 has
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor the CKA1 function when bit 0 of the Interrupt Edge register is 1. Table 6. Divide Ratio SS2 0 0 0 0 1 1 1 1 SS1 0 0 1 1 0 0 1 1 SS0 0 1 0 1 0 1 0 1 Divide Ratio /1 /2 /4 /8 /16 /32 /64 External Clock
1
ASCI STATUS REGISTER 0, 1 (STAT0, 1)
Each channel status register allows interrogation of ASCI communication, error and modem control signal status, and enabling or disabling of ASCI interrupts.
ASCI Status Register 0 (STAT0: I/O Address = 04H) Bit 7 RDRF R 6 OVRN R 5 PE R 4 FE R 3 RE R/W 2 DCD0 R 1 TDRE R 0 TIE R/W
ASCI Status Register 1 (STAT1: I/O Address = 05H) Bit 7 RDRF R 6 OVRN R 5 PE R 4 FE R 3 RE R/W 2 CTSIE R/W 1 TDRE R 0 TIE R/W
Figure 35. ASCI Status Registers
RDRF: Receive Data Register Full (bit 7). RDRF is set to 1 when an incoming data byte is loaded into an empty Rx FIFO. Note that if a framing or parity error occurs, RDRF is still set and the receive data (which generated the error) is still loaded into the FIFO. RDRF is cleared to 0 by reading RDR and last character in the FIFO from IOSTOP mode, during RESET and for ASCI0 if the /DCD0 input is auto-enabled and is negated (High). OVRN: Overrun Error (bit 6). An overrun condition occurs if the receiver has finished assembling a character but the Rx FIFO is full so there is no room for the character. However, this status bit is not set until the last character received before the overrun becomes the oldest byte in the FIFO. This bit is cleared when software writes a 1 to the
EFR bit in the CNTLA register, and also by Reset, in IOSTOP mode, and for ASCI0 if the /DCD0 pin is auto enabled and is negated (High). Note that when an overrun occurs, the receiver does not place the character in the shift register into the FIFO, nor any subsequent characters, until the last good character has come to the top of the FIFO so that OVRN is set, and software then writes a 1 to EFR to clear it.
DS971800401
PRELIMINARY
1-41
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor PE: Parity Error (bit 5). A parity error is detected when parity checking is enabled by the MOD1 bit in the CNT1LA register being 1, and a character has been assembled in which the parity does not match the PEO bit in the CNTLB register. However, this status bit is not set until/unless the error character becomes the oldest one in the RxFIFO. PE is cleared when software writes a 1 to the EFR bit in the CNTRLA register, and also by Reset, in IOSTOP mode, and for ASCI0 if the /DCD0 pin is auto-enabled and is negated (High). FE: Framing Error (bit 4). A framing error is detected when the stop bit of a character is sampled as 0/Space. However, this status bit is not set until/unless the error character becomes the oldest one in the RxFIFO. FE is cleared when software writes a 1 to the EFR bit in the CNTLA register, and also by Reset, in IOSTOP mode, and for ASCIO if the /DCDO pin is auto-enabled and is negated (High). REI: Receive Interrupt Enable (bit 3). RIE should be set to 1 to enable ASCI receive interrupt requests. When RIE is 1, the Receiver requests an interrupt when a character is received and RDRF is set, but only if neither DMA channel has its Request-routing field set to receive data from this ASCI. That is, if SM1-0 are 11 and SAR17-16 are 10, or DIM1 is 1 and IAR17-16 are 10, then ASCI1 doesn't request an interrupt for RDRF. If RIE is 1, either ASCI requests an interrupt when OVRN, PE or FE is set, and
Zilog ASCI0 requests an interrupt when /DCD0 goes High. RIE is cleared to 0 by Reset. DCD0: Data Carrier Detect (bit 2 STAT0). This bit is set to 1 when the pin is High. It is cleared to 0 on the first read of STAT0 following the pin's transition from High to Low and during RESET. Bit 6 of the ASEXT0 register is 0 to select auto-enabling, and the pin is negated (High). Channel 1 has an external CTS1 input which is multiplexed with the receive data pin RSX for the CSI/O. Bit 2 = 0; Select RXS function. Bit 2 = 1; Select CTS1 function. TDRE: Transmit Data Register Empty (bit 1). TDRE = 1 indicates that the TDR is empty and the next transmit data byte is written to TDR. After the byte is written to TDR, TDRE is cleared to 0 until the ASCI transfers the byte from TDR to the TSR and then TDRE is again set to 1. TDRE is set to 1 in IOSTOP mode and during RESET. On ASCIO, if the CTS0 pin is auto-enabled in the ASEXT0 registers and the pin is High, TDRE is reset to 0. TIE: Transmit Interrupt Enable (bit 0). TIE should be set to 1 to enable ASCI transmit interrupt requests. If TIE = 1, an interrupt will be requested when TDRE = 1. TIE is cleared to 0 during RESET.
ASCI TRANSMIT DATA REGISTERS
Register addresses 06H and 07H hold the ASCI transmit data for channel 0 and channel 1, respectively. Channel 0 Address (07H) Mnemonics TDR0 Address (06H) 7 -7 -6 -5 -4 -3 -2 -1 -0 -ASCI Transmit Channel 1 Figure 37. ASCI Register 6 -5 -4 -3 -2 -1 -0 -Channel 1 Mnemonics TDR1
ASCI Transmit Channel 0 Figure 36. ASCI Register
1-42
PRELIMINARY
DS971800401
Zilog
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor Channel 1-Mnemonics TSR1 Address (09H)
ASCI Receive Register
Register addresses 08H and 09H hold the ASCI receive data for channel 0 and channel 1, respectively. Channel 0 Mnemonics TSR0 -Address (08H)
1
5 -4 -3 -2 -1 -0 --
7 --
6 --
7 --
6 --
5 --
4 --
3 --
2 --
1 --
0 --
ASCI Transmit Data Figure 39. ASCI Receive Register Channel 1R
ASCI Transmit Data Figure 38. ASCI Receive Register Channel 0
CSI/O CONTROL/STATUS REGISTER
(CNTR: I/O Address = 0AH). CNTR is used to monitor CSI/O status, enable and disable the CSI/O, enable and disable interrupt generation, and select the data clock speed and source.
Bit
7
6
5
4
3 __
2
1
0
EF R
EIE R/W
RE R/W
TE R/W
SS2 R/W
SS1 R/W
SS0 R/W
Figure 40. CSI/O Control Register
EF: End Flag (bit 7). EF is set to 1 by the CSI/O to indicate completion of an 8-bit data transmit or receive operation. If EIE (End Interrupt Enable) bit = 1 when EF is set to 1, a CPU interrupt request is generated. Program access of TRDR only occurs if EF = 1. The CSI/O clears EF to 0 when TRDR is read or written. EF is cleared to 0 during RESET and IOSTOP mode. EIE: End Interrupt Enable (bit 6). EIE is set to 1 to generate a CPU interrupt request. The interrupt request is inhibited if EIE is reset to 0. EIE is cleared to 0 during RESET. RE: Receive Enable (bit 5). A CSI/O receive operation is started by setting RE to 1. When RE is set to 1, the data clock is enabled. In internal clock mode, the data clock is output from the CKS pin. In external clock mode, the clock
is input on the CKS pin. In either case, data is shifted in on the RXS pin in synchronization with the (internal or external) data clock. After receiving 8 bits of data, the CSI/O automatically clears RE to 0, EF is set to 1, and an interrupt (if enabled by EIE = 1) is generated. RE and TE are never both set to 1 at the same time. RE is cleared to 0 during RESET and ISTOP mode.
DS971800401
PRELIMINARY
1-43
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor Transmit Enable (bit 4). A CSI/O transmit operation is started by setting TE to 1. When TE is set to 1, the data clock is enabled. When in internal clock mode, the data clock is output from the CKS pin. In external clock mode, the clock is input on the CKS pin. In either case, data is shifted out on the TXS pin synchronous with the (internal or external) data clock. After transmitting 8 bits of data, the CSI/O automatically clears TE to 0, EF is set to 1, and an interrupt (if enabled by EIE = 1) is generated. TE and RE are never both set to 1 at the same time. TE is cleared to 0 during RESET and IOSTOP mode. SS2, 1, 0: Speed Select 2, 1, 0 (bits 2-0). SS2, SS1 and SS0 select the CSI/O transmit/receive clock source and speed. SS2, SS1 and SS0 are all set to 1 during RESET. Table 10 shows CSI/O Baud Rate Selection. Table 7. CSI/O Baud Rate Selection SS2 0 0 0 0 1 1 1 1 SS1 0 0 1 1 0 0 1 1 SS0 0 1 0 1 0 1 0 1 Divide Ratio /20 /40 /80 /160 /320 /640 /1280 External Clock Input (less than /20.)
Zilog
Timer Data Register Channel 0L
TMDR0L 0CH
7 --
6 --
5 --
4 --
3 --
2 --
1 --
0 --
ASCI Receive Data Figure 42. Timer Register Channel OL
Timer Data Register Channel 0H
TMDR0H 0D H
7 --
6 --
5 --
4 --
3 --
2 --
1 --
0 --
Timer Data Figure 43. Timer Data Register Channel OH
After RESET, the CKS pin is configured as an external clock input (SS2, SS1, SS0 = 1). Changing these values causes CKS to become an output pin and the selected clock is output when transmit or receive operations are enabled.
CSI/O Transmit/Receive Data Register
(TRDR: I/O Address = 0BH).
7 --
6 --
5 --
4 --
3 --
2 --
1 --
0 --
CSI/O T/R Data Figure 41. CSI/O Transmit/Receive Data Register 1R
1-44
PRELIMINARY
DS971800401
Zilog
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
Timer Reload Register 0L
RLDR0L 0E H
Timer Reload Register 0H
RLDR0H 0F H
1
7 -6 -5 -4 -3 -2 -1 -0 --
7 --
6 --
5 --
4 --
3 --
2 --
1 --
0 --
Timer Reload Data Figure 44. Timer Reload Register Low
Timer Reload Data Figure 45. Timer Reload Register Channel
TIMER CONTROL REGISTER (TCR)
TCR monitors both channels (PRT0, PRT1) TMDR status. It also controls enabling and disabling of down counting and interrupts along with controlling output pin A18/TOUT for PRT1.
Bit
7 TIF1 R
6 TIF0 R
5 TIE1 R/W
4 TIE0 R/W
3 TOC1 R/W
2 TOC0 R/W
1 TDE1 R/W
0 TDE0 R/W
Figure 46. Timer Control Register (TCR: I/O Address = 10H)
TIF1: Timer Interrupt Flag 1 (bit 7). When TMDR1 decrements to 0, TIF1 is set to 1. This generates an interrupt request if enabled by TIE1 = 1. TIF1 is reset to 0 when TCR is read and the higher or lower byte of TMDR1 is read. During RESET, TIF1 is cleared to 0. TIF0: Timer Interrupt Flag 0 (bit 6). When TMDR0 decrements to 0, TIF0 is set to 1. This generates an interrupt request if enabled by TIE0 = 1. TIF0 is reset to 0 when TCR is read and the higher or lower byte of TMDR0 is read. During RESET, TIF0 is cleared to 0. TIE1: Timer Interrupt Enable 1 (bit 5). When TIE0 is set to 1, TIF1 = 1 generates a CPU interrupt request. When TIE0 is reset to 0, the interrupt request is inhibited. During RESET, TIE0 is cleared to 0.
TOC1, 0: Timer Output Control (bits 3, 2). TOC1 and TOC0 control the output of PRT1 using the multiplexed TOUT/DREQ pin as shown in Table 11. During RESET, TOC1 and TOC0 are cleared to 0. If bit 3 of the IAR1B register is 1, the TOUT function is selected. By programming TOC1 and TOC0, the TOUT/DREQ pin can be forced High, Low, or toggled when TMDR1 decrements to 0. Table 8. Timer Output Control TOC1 TOC0 0 0 1 1 0 1 0 1 Output Inhibited The TOUT/DREQ pin is not affected by the PRT. Toggled If bit 3 of IAR1B is 1, the TOUT/DREQ pin is toggles or 0 set Low or High as indicated. 1
DS971800401
PRELIMINARY
1-45
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor TDE1, 0: Timer Down Count Enable (bits 1, 0). TDE1 and TDE0 enable and disable down counting for TMDR1 and TMDR0, respectively. When TDEn (n = 0, 1) is set to
Zilog 1, down counting is stopped and TMDRn is freely read or written. TDE1 and TDE0 are cleared to 0 during RESET and TMDRn will not decrement until TDEn is set to 1.
ASCI EXTENSION CONTROL REGISTER CHANNEL 0 (ASEXT0) AND CHANNEL 1 (ASEXT1)
Note: This register controls functions that have been added to the ASCIs in the Z80180/Z8S180/Z8L180 family. Note: All bits in this register reset to zero.
ASCI Extension Control Register 0(ASEXT0 I/O Address = 12H) Bit 7 6 5 CTSO 4 XI 3 BRGO Mode 2 Break Nab 1 Break 0 Send Break
Reserved DCDO Bit 7
ASCI Extension Control Register 1 (ASEXT1 I/O Address = 13H) 3 5 4 2 1 0 6 XI BRGI Mode Break Enab Break Send Break
Reserved Reserved Reserved
Figure 47. ASCI Extension Control Registers, Channel 0 and 1
DCD0 dis (bit 6, ASCI0 only). If this bit is 0, then the DCD0 pin "auto-enables" the ASCI0 receiver, such that when the pin is negated/High, the Receiver is held in a RESET state. The state of the DCD-pin has no effect on receiver operation. In either state of this bit, software can read the state of the DCD0 pin in the STAT0 register, and the receiver will interrupt on a rising edge of DCD0. CTS0 dis (bit 5, ASCI0 only). If this bit is 0, then the CTS0 pin "auto-enables" the ASCIO transmitter, in that when the pin is negated/high, the TDRE bit in the STAT0 register is forced to 0. If this bit is 1, the state of the CTS0 pin has no effect on the transmitter. Regardless of the state of this bit, software can read the state of the CTS0 pin the CNTLB0 register. X1 (bit 4). If this bit is 1, the clock from the Baud Rate Generator or CKA pin is taken as a "1X" bit clock (this is sometimes called "isochronous" mode). In this mode, receive data on the RXA pin must be synchronized to the clock on the CKA pin, regardless of whether CKA is an input or an output. If this bit is 0, the clock from the Baud Rate Generator or CKA pin is divided by 16 or 64 per the DR bit in CNTLB register, to obtain the actual bit rate. In this mode, receive data on the RxA pin need not be synchronized to a clock. BRG Mode (bit 3). If the SS2-0 bits in the CNTLB register are not 111, and this bit is 0, this ASCI's Baud Rate Generator divides PHI by 10 or 30, depending on the DR bit in CNTLB, and then by a power of two selected by the SS2-
0 bits, to obtain the clock that is presented to the transmitter and receiver and that can be output on the CKA pin. If SS2-0 are not 111, and this bit is 1, the Baud Rate Generator divides PHI by twice (the 16-bit value programmed into the Time Constant Registers, plus two). This mode is identical to the operation of the baud rate generator in the ESCC. Break Enable (bit 2). If this bit is 1, the receiver will detect Break conditions and report them in bit 1, and the transmitter will send Breaks under the control of bit 0. Break Detect (bit 1). The receiver sets this read-only bit to 1 when an all-zero character with a Framing Error becomes the oldest character in the Rx FIFO. The bit is cleared when software writes a 0 to the EFR bit in CNTLA register, also by Reset, by IOSTOP mode, and for ASCIO if the DCD0 pin is auto-enabled and is negated (high). Send Break (bit 0). If this bit and bit 2 are both 1, the transmitter holds the TXA pin low to send a Bread condition. The duration of the Bread is under software control (one of the PRTs or CTCs can be used to time it). This bit resets to 0, in which state TXA carries the serial output of the transmitter.
1-46
PRELIMINARY
DS971800401
Zilog
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
Timer Data Register Channel 1L
Mnemonic TMDR1L Address 14
Timer Reload Register Channel 1L
Mnemonic RLDR1H Address 17
1
6 5 4 3 2 1 0
7
6
5
4
3
2
1
0
7
Timer Data
Reload Data Figure 51. Timer Relaod Register Channel 1L
Figure 48. Timer Data Register 1L
Timer Data Register Channel 1H
Mnemonic TMDR1H Address 15
Free Running Counter (Read Only)
Mnemonic FRC Address 18
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
Timer Data Figure 49. Timer Data Register 1H
Counting Data Figure 52. Free Running Counter
Timer Reload Register Channel 1L
Mnemonic RLDR1L Address 16
7
6
5
4
3
2
1
0
Reload Data Figure 50. Timer Reload Channel 1L
DS971800401
PRELIMINARY
1-47
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
Zilog
ASCI TIME CONSTANT REGISTERS
If the SS2-0 bits of the CNTLA register are not 111, and the BRG Mode bit in the ASEXT register is 1, the ASCI divides the PHI clock by twice (the 16-bit value in these registers, plus two), to obtain the clock that is presented to the transmitter and receiver for division by 1, 16, or 64 and that can be output on the CKA1 pin.
ASCI Time Constant Register 0 Low (ASTCOL, I/O Address IAH) ASCI Time Constant Register 1 Low (ASTCIL), I/O Address ICH) Bit 7 6 5 4 3 2 1 0
LS 8 Bits of Time Constant
ASCI Time Constant Register 0 High (ASTCOH, I/O Address IBH) ASCI Time Constant Register 1 High (ASTCIH), I/O Address IDH) Bit 7 6 5 4 3 2 1 0
MS 8 Bits of Time Constant
Figure 53. ASCI Time Constant Registers
1-48
PRELIMINARY
DS971800401
Zilog
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
CLOCK MULTIPLIER REGISTER (Z180 MPU ADDRESS 1EH)
7 0 6 0 5 1 4 1 3 1 2 1 1 1 0 1 Bit 6. Low Noise Crystal Option. Setting this bit to 1 will enable the low noise option for the EXTAL and XTAL pins. This option reduces the gain, in addition to reduction the output drive capability to 30% of its original drive capability. The Low Noise Crystal Option is recommended in the use of crystals for PCMCIA applications where the crystal may be driven too hard by the oscillator. Setting this bit to 0 will select for normal operation of the EXTAL and XTAL pins. The default for this bit is 0. Note: Operating restrictions for device operation are listed below. If low noise option is required, and normal device operation is needed, use the clock multiplier feature. Table 9. Low Noise Option Low Noise ADDR 1E, bit 6=1 20 MHz @ 4.5V, 100C 10 MHz @ 3.0V, 100C Normal ADDR 1E, bit 6=0 33 MHz @ 4.5V, 100C 20 MHz @ 3.0V, 100C
1
RESERVED LOW NOISE CRYSTAL X2 CLOCK MULTIPLIER
Figure 54. Clock Multiplier Register Bit 7. X2 Clock Multiplier Mode. When this bit is set to 1, this allows the programmer to double the internal clock from that of the external clock. This feature will only operated effectively with frequencies of 10-16 MHz (20-32MHz internal). When this bit is set to 0, the Z80180/Z8S180/Z8L180 device will operate in normal mode. Upon powerup, this feature is disabled.
DS971800401
PRELIMINARY
1-49
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
Zilog
DMA SOURCE ADDRESS REGISTER CHANNEL 0
(SAR0: I/O Address = 20H to 22H) specifies the physical source address for channel 0 transfers. The register contains 20 bits and can specify up to 1024 KB memory addresses or up to 64 KB I/O addresses. Channel 0 source can be memory, I/O, or memory mapped I/O. For I/O, the MS bits of this register identify the Request Handshake signal.
DMA Source Address Register, Channel 0L
Mnemonic SAR0L Address 20
DMA Source Address Register Channel 0B
Mnemonics SAR0B Address 22
7 --
6 --
5 --
4 --
3 --
2 --
1 --
0 --
7 --
6 --
5 --
4 --
3 --
2 --
1 --
0 --
DMA Channel 0 Address Figure 55. DMA Source Address Register 0L
DMA Channel B Address Figure 57. DMA Source Address Register 0B
DMA Source Address Register, Channel 0H
Mnemonic SAR0H Address 21
7 --
6 --
5 --
4 --
3 --
2 --
1 --
0 --
DMA Channel 0 Address Figure 56. DMA Source Address Register 0H
1-50
PRELIMINARY
DS971800401
Zilog
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
DMA DESTINATION ADDRESS REGISTER CHANNEL 0
(DAR0: I/O Address = 23H to 25H) specifies the physical destination address for channel 0 transfers. The register contains 20 bits and can specify up to 1024 KB memory addresses or up to 64 KB I/O addresses. Channel 0 destination can be memory, I/O, or memory mapped I/O. For I/O, the MS bits of this register identify the Request Handshake signal for channel 0.
1
DMA Destination Address Register Channel 0L
Mnemonic DAR0L Address 23
DMA Destination Address Register Channel 0B
Mnemonic DAR0B Address 25
Figure 58. DMA Destination Address Register Channel 0L
Figure 60. DMA Destination Address Register Channel 0B Note: In the R1 and Z Mask, these DMA registers are expanded from 4 bit to 3 bits in the package version of CP68 A19* X X X X A18 X X X X A17 0 0 1 1 A16 0 1 0 1 DMA Transfer Request DREQ0 TDR0 (ASCI0) TDR1 (ASCI1) Not Used
DMA Destination Address Register Channel 0H
Mnemonic DAR0H Address 24
Figure 59. DMA Destination Address Register Channel 0H
DS971800401
PRELIMINARY
1-51
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
Zilog
DMA BYTE COUNT REGISTER CHANNEL 0
(BCRO: I/O Address = 26H to 27H) specifies the number of bytes to be transferred. This register contains 16 bits and may specify up to 64 KB transfers. When one byte is transferred, the register is decremented by one. If "n" bytes should be transferred, "n" must be stored before the DMA operation. Note: All DMA Count Register channels are undefined during reset.
DMA Byte Count Register Channel 0L
Mnemonic BCR0L Address 26
DMA Byte Count Register Channel 1L
Mnemonic BCR1L Address 2E
Figure 61. DMA Byte Count Register 0L
Figure 63. DMA Byte Count Register 1L
DMA Byte Count Register Channel 0H
Mnemonic BCR0H Address 27
DMA Byte Count Register Channel 0H
Mnemonic BCR1H Address 2F
Figure 62. DMA Byte Count Register 0H
Figure 64. DMA Byte Count Register 0H
1-52
PRELIMINARY
DS971800401
Zilog
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
DMA MEMORY ADDRESS REGISTER CHANNEL 1
(MAR1: I/O Address = 28H to 2AH) specifies the physical memory address for channel 1 transfers. This may be destination or source memory address. The register contains 20 bits and may specify up to 1024 KB memory address.
1
DMA Memory Address Register, Channel 1L
Mnemonic MAR1L Address 28
DMA Memory Address Register, Channel 1B
Mnemonic MAR1B Address 2A
Figure 65. DMA Memory Address Register, Channel 1L
Figure 67. DMA Memory Address Register, Channel 1B
DMA Memory Address Register, Channel 1H.
Mnemonic MAR1H Address 29
Figure 66. DMA Memory Address Register, Channel 1H
DS971800401
PRELIMINARY
1-53
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
Zilog
DMA I/O ADDRESS REGISTER CHANNEL 1
(IAR1: I/O Address = 2BH to 2DH) specifies the I/O address for channel 1 transfers. This may be destination or source I/O address. The register contains 16 bits of I/O address; its most significant byte identifies the Request Handshake signal and controls the Alternating Channel feature. All bits in IAR1B reset to 0.
Bit
7 A/T F
6 A/T C
5
4
3 TOUT /DREQ
2
1 Req 1 Sel
0
Figure 68. IAR MS Byte Register (IARIB: I/O Address 2DH)
DMA I/O Address Register Channel 1L
Mnemonic IAR1L Address 2B
DMA I/O Address Register Channel 1B
Mnemonic IAR1B Address 2D
Figure 69. DMA I/O Address Register Channel 1L
Figure 71. DMA I/O Address Register Channel 1B
DMA I/O Address Register Channel 1H
Mnemonic IAR1H Address 2C
Figure 70. DMA I/O Address Register Channel 1H
1-54
PRELIMINARY
DS971800401
Zilog
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
DMA STATUS REGISTER (DSTAT)
DSTAT is used to enable and disable DMA transfer and DMA termination interrupts. DSTAT also indicates DMA transfer status, in other words, completed or in progress. Mnemonic DSTAT Address 30
1
1 0 DME R
Bit
7 DE1 R/W
6 DE0 R/W
5 DWE1 W
4 DWE0 W
3 DIE1 R/W
2 DIE0 R/W
Figure 72. DMA Status Register (DSTAT: I/O Address = 30H)
DE1: DMA Enable Channel 1 (bit 7). When DE1 = 1 and DME = 1, channel 1 DMA is enabled. When a DMA transfer terminates (BCR1 = 0), DE1 is reset to 0 by the DMAC. When DE1 = 0 and the DMA interrupt is enabled (DIE1 = 1), a DMA interrupt request is made to the CPU. To perform a software write to DE1, DWE1 should be written with 0 during the same register write access. Writing DE1 to 0 disables channel 1 DMA, but DMA is restartable. Writing DE1 to 1 enables channel 1 DMA and automatically sets DME (DMA Main Enable) to 1. DE1 is cleared to 0 during RESET. DE0: DMA Enable Channel 0 (bit 6). When DE0 = 1 and DME = 1, channel 0 DMA is enabled. When a DMA transfer terminates (BCR0 = 0), DE0 is reset to 0 by the DMAC. When DE0 = 0 and the DMA interrupt is enabled (DIE0 = 1), a DMA interrupt request is made to the CPU. To perform a software write to DE0, DWE0 should be written with 0 during the same register write access. Writing DE0 to 0 disables channel 0 DMA. Writing DE0 to 1 enables channel 0 DMA and automatically sets DME (DMA Main Enable) to 1. DE0 is cleared to 0 during RESET. DWE1: DE1 Bit Write Enable (bit 5). When performing any software write to DE1, DWE1 should be written with 0 during the same access. DWE1 always reads as 1.
DWE0: DE0 Bit Write Enable (bit 4). When performing any software write to DE0, DWE0 should be written with 0 during the same access. DWE0 always reads as 1. DIE1: DMA Interrupt Enable Channel 1 (bit 3). When DIE0 is set to 1, the termination channel 1 DMA transfer (indicated when DE1 = 0) causes a CPU interrupt request to be generated. When DIE0 = 0, the channel 0 DMA termination interrupt is disabled. DIE0 is cleared to 0 during RESET. DIE0: DMA Interrupt Enable Channel 0 (bit 2). When DIE0 is set to 1, the termination channel 0 of DMA transfer (indicated when DE0=0) causes a CPU interrupt request to be generated. When DIE0=0, the channel 0 DMA termination interrupt is disabled. DIE0 is cleared to 0 during RESET. DME: DMA Main Enable (bit 0). A DMA operation is only enabled when its DE bit (DE0 for channel 0, DE1 for channel 1) and the DME bit is set to 1. When NMI occurs, DME is reset to 0, thus disabling DMA activity during the NMI interrupt service routine. To restart DMA, DE- and/or DE1 should be written with 1 (even if the contents are already 1). This automatically sets DME to 1, allowing DMA operations to continue. Note that DME cannot be directly written. It is cleared to 0 by NMI or indirectly set to 1 by setting DE0 and/or DE1 to 1. DME is cleared to 0 during RESET.
DS971800401
PRELIMINARY
1-55
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
Zilog
DMA MODE REGISTER (DMODE).
DMODE is used to set the addressing and transfer mode for channel 0. Mnemonic DMODE Address 31H
Bit
7
6
5 DM1 R/W
4 DM0 R/W
3 SM1 R/W
2 SM0 R/W
1 MMOD R/W
0
Figure 73. DMA Mode Register (DMODE: I/O Address = 31H)
DM1, DM0: Destination Mode Channel 0 (bits 5,4) specifies whether the destination for channel 0 transfers is memory or I/O, and whether the address should be incremented or decremented for each byte transferred. DM1 and DM0 are cleared to 0 during RESET. Table 10. Channel 0 Destination Memory Increment/Decrement +1 -1 fixed fixed
SM1, SM0: Source Mode Channel 0 (bits 3, 2) specifies whether the source for channel 0 transfers is memory or I/O, and whether the address should be incremented or decremented for each byte transferred. Table 11. Channel 0 Source Memory Increment/Decrement +1 -1 fixed fixed
SM1 0 0 1 1
SM0 0 1 0 1
Memory I/O Memory Memory Memory I/O
DM1 0 0 1 1
DM0 0 1 0 1
Memory I/O Memory Memory Memory I/O
1-56
PRELIMINARY
DS971800401
Zilog Table 12 shows all DMA transfer mode combinations of DM0, DM1, SM0, and SM1. Since I/O to/from I/O transfers
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor are not implemented, 12 combinations are available.
Table 12. Transfer Mode Combinations Address Increment/Decrement SAR0+1, DAR0+1 SAR0-1, DAR0+1 SAR0 fixed, DAR0+1 SAR0 fixed, DAR0+1 SAR0+1, DAR0-1 SAR0-1, DAR0-1 SAR0 fixed, DAR0-1 SAR0 fixed, DAR0-1 SAR0+1, DAR0 fixed SAR0-1, DAR0 fixed
1
DM1
DM0
SM1
SM0
Transfer Mode MemoryMemory MemoryMemory Memory*Memory I/OMemory MemoryMemory MemoryMemory Memory*Memory I/OMemory MemoryMemory* MemoryMemory* Reserved Reserved MemoryI/O Memory I/O Reserved Reserved
0 0 0 0 0 0 0 1 0 0 1 0 0 0 1 1 0 1 0 0 0 1 0 1 0 1 1 0 0 1 1 1 1 0 0 0 1 0 0 1 1 0 1 0 1 0 1 1 1 1 0 0 1 1 0 1 1 1 1 0 1 1 1 0 Note: * Includes memory mapped I/O.
SAR0+1, DAR0 fixed SAR0-1, DAR0 fixed
MMOD: Memory Mode Channel 0 (bit). When channel 0 is configured for memory to/from memory transfers there is no Request Handshake signal to control the transfer timing. Instead, two automatic transfer timing modes are selectable: burst (MMOD = 1) and cycle steal (MMOD = 0). For burst memory to/from memory transfers, the DMAC takes control of the bus continuously until the DMA transfer completes (as shown by the byte count register = 0). In cycle steal mode, the CPU is given a cycle for each DMA byte transfer cycle until the transfer is completed.
For channel 0 DMA with I/O source or destination, the selected Request signal times the transfer and thus MMOD is ignored. MMOD is cleared to 0 during RESET.
DS971800401
PRELIMINARY
1-57
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
Zilog
DMA/WAIT CONTROL REGISTER (DCNTL)
DCNTL controls the insertion of wait states into DMAC (and CPU) accesses of memory or I/O. Also, it defines the Request signal for each channel as level or edge sense. DCNTL also sets the DMA transfer mode for channel 1, which is limited to memory to/from I/O transfers.
Bit
7
6
5 IWI1 R/W
4 IWI0 R/W
3
2
1 DIM1 R/W
0 DIM0 R/W
MWI1 MWI0 R/W R/W
DMS1 DMS0 R/W R/W
Figure 74. DMA/WAIT Control Register (DCNTL: I/O Address = 32H)
MWI1, MWI0: Memory Wait Insertion (bits 7-6). Specifies the number of wait states introduced into CPU or DMAC memory access cycles. MWI1 and MWI0 are set to 1 during RESET. MWI1 0 0 1 1 MWI0 0 1 0 1 Wait State 0 1 2 3
DMS1, DMS0: DMA Request Sense (bits 3-2). DMS1 and DMS0 specify the DMA request sense for channel 0 and channel 1 respectively. When reset to 0, the input is level sense. When set to 1, the input is edge sense. DMS1 and DMS0 are cleared to 0 during RESET. DMSi 1 0 Sense Edge Sense Level Sense
IWI1, IWI0: I/O Wait Insertion (bits 5-4). Specifies the number of wait states introduced into CPU or DMAC I/O access cycles. IWI1 and IWI0 are set to 1 during RESET. See the section on Wait-State Generation for details. IWI1 0 0 1 1 IWI0 0 1 0 1 Wait State 0 2 3 4
Typically, for an input/source device, the associated DMS bit should be programmed as 0 for level sense because the device has a relatively long time to update its Request signal after the DMA channel reads data from it in the first of the two machine cycles involved in transferring a byte. An output/destination device has much less time to update its Request signal, after the DMA channel starts a write operation to it, as the second machine cycle of the two cycles involved in transferring a byte. With zero-wait state I/O cycles, which apply only to the ASCIs, it is impossible for a device to update its Request signal in time, and edge sensing must be used.
1-58
PRELIMINARY
DS971800401
Zilog With one-wait-state I/O cycles (the fastest possible except for the ASCIs), it is unlikely that an output device will be able to update its Request in time, and edge sense is required. DIM1, DIM0: DMA Channel 1 I/O and Memory Mode (bits 1-0). Specifies the source/destination and address
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor modifier for channel 1 memory to/from I/O transfer modes. DIM1 and DIM0 are cleared to 0 during RESET. Table 13. Channel 1 Transfer Mode Address Increment/Decrement MAR1 +1, IAR1 fixed MAR1-1, IAR1 fixed IAR1 fixed, MAR1 + 1 IAR1 fixed, MAR1 -1
1
DIM1 DMI0 Transfer Mode 0 0 1 1 0 1 0 1 MemoryI/O MemoryI/O I/OMemory I/OMemory
INTERRUPT VECTOR LOW REGISTER
Mnemonic: IL Address 33 Bits 7-5 of IL are used as bits 7-5 of the synthesized interrupt vector during interrupts for the INT1 and INT2 pins and for the DMAs, ASCIs, PRTs, and CSI/O. These three bits are cleared to 0 during Reset (Figure 75).
Bit
7 IL 7 R/W
6 IL 6 R/W
5 IL 5 R/W
4 --
3 --
2 --
1 --
0 --
Programmable
Interrupt Source Dependent Code
Figure 75. Interrupt Vector Low Register (IL: I/O Address = 33H)
INT/TRAP CONTROL REGISTER
Mnemonics ITC Address 34 INT/TRAP Control Register (ITC, I/O Address 34H). This register is used in handling TRAP interrupts and to enable or disable Maskable Interrupt Level 0 and the INT1 and INT2 pins. the starting address of the undefined instruction. This is necessary since the TRAP may occur on either the second or third byte of the Opcode. UFO allows the stacked PC value to be correctly adjusted. If UFO = 0, the first Opcode should be interpreted as the stacked PC-1. If UFO = 1, the first Opcode address is stacked PC-2. UFO is Read-Only. ITE2, 1, 0: Interrupt Enable 2, 1, 0 (bits 2-0). ITE2 and ITE1 enable and disable the external interrupt inputs /INT2 and /INT1, respectively. ITE0 enables and disables interrupts from the on-chip ESCC, CTCs and Bidirectional Centronics controller as well as the external interrupt input /INT0. A 1 in a bit enables the corresponding interrupt level while a 0 disables it. A Reset sets ITE0 to 1 and clears ITE1 and ITE2 to 0. TRAP Interrupt. The Z80180/Z8S180/Z8L180 generates a non-maskable (not affected by the state of IEF1) TRAP interrupt when an undefined Opcode fetch occurs. This feature can be used to increase software reliability, implement an "extended" instruction set, or both. TRAP may occur during Opcode fetch cycles and also if an undefined
Bit
7
6
5 --
4 --
3 --
2
1
0
TRAP UFO R/W R
ITE2 ITE1 ITE0 R/W R/W R/W
TRAP (bit 7). This bit is set to 1 when an undefined Opcode is fetched. TRAP can be reset under program control by writing it with a 0, however, it cannot be written with 1 under program control. TRAP is reset to 0 during RESET. UFO: Undefined Fetch Object (bit 6). When a TRAP interrupt occurs, the contents of UFO allow determination of
DS971800401
PRELIMINARY
1-59
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor Opcode is fetched during the interrupt acknowledge cycle for INT0 when Mode 0 is used. When a TRAP interrupt occurs, Z80180/Z8S180/Z8L180 operates as follows: the
Zilog in ITC will reveal whether the restart at physical address 00000H was caused by RESET or TRAP. All TRAP interrupts occur after fetching an undefined second Opcode byte following one of the "prefix" Opcodes CBH, DDH, EDH, or FDH, or after fetching an undefined third Opcode byte following one of the "double prefix" Opcodes DDCBH or FDCBH. The state of the Undefined Fetch Object (UFO) bit in ITC allows TRAP software to correctly "adjust" the stacked PC, depending on whether the second or third byte of the Opcode generated the TRAP. If UFO=0, the starting address of the invalid instruction is equal to the stacked PC-1. If UFO=1, the starting address of the invalid instruction is equal to the stacked PC-2.
1. The TRAP bit in the Interrupt TRAP/Control (ITC) register is set to 1. 2. The current PC (Program Counter) value, reflecting the location of the undefined Opcode, is saved on the stack. 3. The Z80180/Z8S180/Z8L180 vectors to logical address 0. Note that if logical address 0000H is mapped to physical address 00000H, the vector is the same as for RESET. In this case, testing the TRAP bit
Restart from 0000H 2nd Opcode Fetch Cycle PC Stacking TTP Ti Ti Ti Ti Ti T1 T2 T3 T1 T2 T3 T1 Opcode Fetch Cycle T2 T3
A0-A18 (A19) D0-D7
T1
T2
T3
PC
SP-1 PCH
SP-2 PCL
0000H
Undefined Opcode M1 MREQ RD WR
Figure 76. TRAP Timing-2nd Opcode Undefined
1-60
PRELIMINARY
DS971800401
Zilog
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
Restart from 0000H 3nd Opcode Fetch Cycle Memory Read Cycle Ti Ti Ti PC Stacking T1 T2 T3 SP-1 PC-1H Undefined Opcode T1 T2 T3 SP-2 PC-1L Opcode Fetch Cycle T1 T2 T3 0000H
1
A0-A18 (A19) D0-D7 M1 MREQ RD WR
T1 T2 T3 T1 T2 TTP T3 Ti PC IX + d, IY + d
Figure 77. TRAP Timing-3rd Opcode Undefined
REFRESH CONTROL REGISTER
Mnemonic RCR Address 36 REFE: Refresh Enable (bit 7). REFE = disables the refresh controller while REFE = 1 enables refresh cycle insertion. REFE is set to 1 during RESET. REFW: Refresh Wait (bit 6). REFW = 0 causes the refresh cycle to be two clocks in duration. REFW = 1 causes the refresh cycle to be three clocks in duration by adding a refresh wait cycle (TRW). REFW is set to 1 during RESET. Cyc0 Cyc1 Reserved Figure 78. Refresh Control Register (RCA: I/O Address = 36H) The RCR specifies the interval and length of refresh cycles, while enabling or disabling the refresh function. CYC1, 0: Cycle Interval (bit 1,0). CYC1 and CYC0 specify the interval (in clock cycles) between refresh cycles. In the case of dynamic RAMs requiring 128 refresh cycles every 2 ms (0r 256 cycles in every 4 ms), the required refresh interval is less than or equal to 15.625 s. Thus, the underlined values indicate the best refresh interval depending on CPU clock frequency. CYC0 and CYC1 are cleared to 0 during RESET (see Table 14).
7 -REFE REFW
6 --
5 --
4 --
3 --
2 --
1 --
0 --
DS971800401
PRELIMINARY
1-61
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor Table 14. DRAM Refresh Intervals Insertion Interval 10 states 20 states 40 states 80 states Time Interval 6 MHz 1.66 s 3.3 s 6.6 s 13.3 s
Zilog
CYC1 0 0 1 1
CYC0 0 1 0 1
O: 10 MHz (1.0 s)* (2.0 s)* (4.0 s)* (8.0 s)*
8 MHz (1.25 s)* (2.5 s)* (5.0 s)* (10.0 s)*
4 MHz 2.5 s 5.0 s 10.0 s 20.0 s
2.5 MHz 4.0 s 8.0 s 16.0 s 32.0 s
Note: *calculated interval
Refresh Control and Reset. After RESET, based on the initialized value of RCR, refresh cycles will occur with an interval of 10 clock cycles and be 3 clock cycles in duration. Dynamic RAM Refresh Operation 1. Refresh Cycle insertion is stopped when the CPU is in the following states: a. During RESET b. When the bus is released in response to BUSREQ. c. During SLEEP mode.
which the first refresh cycle occurs after the Z80180/Z8S180/Z8L180 re-acquires the bus depends on the refresh timer and has no timing relationship with the bus exchange. 3. Refresh cycles are suppressed during SLEEP mode. If a refresh cycle is requested during SLEEP mode, the refresh cycle request is internally "latched" (until replaced with the next refresh request). The "latched" refresh cycle is inserted at the end of the first machine cycle after SLEEP mode is exited. After this initial cycle, the time at which the next refresh cycle occurs depends on the refresh time and has no relationship with the exit from SLEEP mode. 4. The refresh address is incremented by one for each successful refresh cycle, not for each refresh. Thus, independent of the number of "missed" refresh requests, each refresh bus cycle will use a refresh address incremented by one from that of the previous refresh bus cycles.
d. During WAIT states. 2. Refresh cycles are suppressed when the bus is released in response to BUSREQ. However, the refresh timer continues to operate. Thus, the time at
MMU COMMON BASE REGISTER
Mnemonic CBR Address 38 MMU Common Base Register (CBR). CBR specifies the base address (on 4 KB boundaries) used to generate a 20bit physical address for Common Area 1 accesses. All bits of CBR are reset to 0 during RESET.
Bit
7 CB7 R/W
6 CB6 R/W
5 CB5 R/W
4 CB4 R/W
3 CB3 R/W
2 CB2 R/W
1 CB1 R/W
0 CB0 R/W
Figure 79. MMU Common Base Register (BBR: I/O Address = 38H)
1-62
PRELIMINARY
DS971800401
Zilog
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
MMU BANK BASE REGISTER (BBR).
Mnemonic BBR Address 39 BBR specifies the base address (on 4 KB boundaries) used to generate a 19-bit physical address for Bank Area accesses. All bits of BBR are reset to 0 during RESET.
1
Bit
7 BB7 R/W
6 BB6 R/W
5 BB5 R/W
4 BB4 R/W
3 BB3 R/W
2 BB2 R/W
1 BB1 R/W
0 BB0 R/W
Figure 80. MMU Bank Base Register (BBR: I/O Address = 39H)
MMU COMMON/BANK AREA REGISTER (CBAR).
Mnemonic CBAR Address 3A CBAR specifies boundaries within the Z80180/Z8S180/Z8L180 64 KB logical address space for up to three areas; Common Area), Bank Area and Common Area 1. MMU Common/Bank Area Register (CBAR: I/O Address = 3 AH) Bit 7 CA3 R/W 6 CA2 R/W 5 CA1 R/W 4 CA0 R/W 3 BA3 R/W 2 BA2 R/W 1 BA1 R/W 0 BA0 R/W
Figure 81. MMU Common/Bank Area Register (CBAR: I/O Address = 3 AH
CA3-CA0:CA (bits 7-4). CA specifies the start (Low) address (on 4 KB boundaries) for the Common Area 1. This also determines the last address of the Bank Area. All bits of CA are set to 1 during RESET.
BA-BA0 (bits 3-0). BA specifies the start (Low) address (on 4 KB boundaries) for the Bank Area. This also determines the last address of the Common Area 0. All bits of BA are set to 1 during RESET.
DS971800401
PRELIMINARY
1-63
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
Zilog
OPERATION MODE CONTROL REGISTER
Mnemonic OMCR Address 3E The Z80180/Z8S180/Z8L180 is descended from two different "ancestor" processors, Zilog's original Z80 and the Hitachi 64180. The Operating Mode Control Register (OMCR) can be programmed to select between certain differences between the Z80 and the 64180. When M1E=1, the M1 output is asserted Low during the opcode fetch cycle, the INT0 acknowledge cycle, and the first machine cycle of the NMI acknowledge. On the Z80180/Z8S180/Z8L180, this choice makes the processor fetch an RETI instruction once, and when fetching an RETI from zero-wait-state memory will use three clock machine cycles which are not fully Z80-timing compatible but are compatible with the on-chip CTCs. When MIE=0, the processor does not drive M1 Low during instruction fetch cycles, and after fetching an RETI instruction once with normal timing, it goes back and re-fetches the instruction using fully Z80-compatible cycles that include driving M1 Low. This may be needed by some external Z80 peripherals to properly decode the RETI instruction.I/O Control Register (ICR). M1E (M1 Enable). This bit controls the M1 output and is set to a 1 during reset.
D7 D6 D5 --
-- --
-- -Reserved IOC (R/W) M1TE (W) M1E (R/W)
Figure 82. Operating Control Register (OMCR: I/O Address = 3EH)
A0-A18 (A19) D0-D7 M1 MREQ RD ST
T1
T2
T3
T1
T2
T3
TI
TI
TI
T1
T2
T3
TI
T1
T2
T3
TI
PC EDH 4DH
PC+1
PC EDH
PC+1 4DH
Figure 83. RETI Instruction Sequence with MIE=0 ICR allows relocating of the internal I/O addresses. ICR also controls enabling/disabling of the IOSTOP mode (Figure 84).
Bit
7 IOA7 R/W
6 IOA6 R/W
5 IOSTP R/W
4 --
3 --
2 --
1 --
0 --
Figure 84. I/O Control Register (ICR: I/O Address = 3FH)
1-64
PRELIMINARY
DS971800401
Zilog IOA7, 6: I/O Address Relocation (bits 7,6). IOA7 and IOA6 relocate internal I/O as shown in Figure 85. Note that
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor the high-order 8 bits of 16-bit internal I/O address are always 0. IOA7 and IOA6 are cleared to 0 during Reset.
1
00FFH IOA7-IOA6 = 1 1 00COH 00BFH IOA7-IOA6 = 1 0 008OH 007OH IOA7- IOA6 = 0 1 004OH 003FH IOA7-IOA6 = 0 0 000OH Figure 85. I/O Address Relocation IOSTP. IOSTOP Mode (bit 5). IOSTOP mode is enabled when IOSTP is set to 1. Normal I/O operation resumes when IOSTOP is reprogrammed or Reset to 0
DS971800401
PRELIMINARY
1-65
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
Zilog
PACKAGE INFORMATION
Figure 86. 80-Pin QFP Package Diagram
1-66
PRELIMINARY
DS971800401
Zilog
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
1
Figure 87. 64-Pin DIP Package Diagram
Figure 88. 68-Pin PLCC Package Diagram
DS971800401
PRELIMINARY
1-67
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
Zilog
ORDERING INFORMATION
Z80180 Z8S180 6, 8, 10MHz 20, 33MHz Z8L180 20MHz
Please check availability before placing order.
CODES Package
F = Plastic Quad Flatpack P = Plastic Dual In Line V = Plastic Leaded Chip Carrier
Temperature
S = 0C to +70C E = -40C to +85C
Speeds
06 = 6 MHz 08 = 8 MHz 10 = 10 MHz 20 = 20 MHz 33 = 33 MHz
Environmental
C = Plastic Standard Example: Z 80180 08 P S C
is a Z80180, 08 MHz, Plastic DIP, 0 to +70C, Standard Flow Environmental Flow Temperature Package Speed Product Number Zilog Prefix
1-68
PRELIMINARY
DS971800401
Zilog (c) 1997 by Zilog, Inc. All rights reserved. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of Zilog, Inc. The information in this document is subject to change without notice. Devices sold by Zilog, Inc. are covered by warranty and patent indemnification provisions appearing in Zilog, Inc. Terms and Conditions of Sale only. Zilog, Inc. makes no warranty, express, statutory, implied or by description, regarding the information set forth herein or regarding the freedom of the described devices from intellectual property infringement. Zilog, Inc. makes no warranty of merchantability or fitness for any purpose. Zilog, Inc. shall not be responsible for any errors that may appear in this document. Zilog, Inc. makes no commitment to update or keep current the information contained in this document.
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor Zilog's products are not authorized for use as critical components in life support devices or systems unless a specific written agreement pertaining to such intended use is executed between the customer and Zilog prior to use. Life support devices or systems are those which are intended for surgical implantation into the body, or which sustains life whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. Zilog, Inc. 210 East Hacienda Ave. Campbell, CA 95008-6600 Telephone (408) 370-8000 FAX 408 370-8056 Internet: http://www.zilog.com
1
DS971800401
PRELIMINARY
1-69
Z80180/Z8S180/Z8L180 Enhanced Z180 Microprocessor
Zilog
1-70
PRELIMINARY
DS971800401

▲Up To Search▲

Price & Availability of Z8L18006FEC

	To Download Z8L18006FEC Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .